Jump to content
SAU Community

Recommended Posts

My definition of Side stepping is;

- Hold the clutch pedal down

- Bring engine to desired RPM

- Move your foot sideways off the clutch ("sidestep") and let the clutch spring take over

All it does is let any little slackness close and let the whole drivetrain lean on the clutch so when you pop it you don't have the little tollerences bang closed. The clutch won't do anything harmfull in comparison to the actual clutch drop

can someone please explain side stepping?

i got a 1.89 60ft by dropping the clutch at 7k with wheel spin all of first on the limiter lol. ran a 12.1

got 315 rwkw with 255/35/18 profile tyre. kept pressure at 36 because it was still bogging down at 6500 rpm .

with my setup how would use do it?

What brand tyres where they cheapies or actual quality?

Reason i ask is my mate cracked a 12.3 on a 34R with nothing but 1.2bar boost on the stock ceramics and a full exhaust with Bridgestone RE01's (still running std injectors, fuel pump, ecu). It was only about 255awkw from memory too.

So is launching the car in 2nd the way to go? Or is that only if you have a certain amount of power at the wheels. Ive got just over 280 awkw so would it be best in first or second?

  • 1 month later...
  • 1 month later...

www.youtube.com/watch?v=l_eR-39CK9Y&sns=em

Hey Xklaba u remember me beating u a few years ago in my old GTR?

Man i suck at Embedding vids with my phone. Have to copy to address bar

yeah I remember, and that smoke was number 2 piston going bye bye, I had run 11.36 before that and I have sence run 11.13 with only 293rwkw and stock turbos :P

hand brake is the best way IF you have a good clutch, other wise no hand brake dial in 7000-7500 and just find friction piont then ride out works for me

second gear launchs in standed ratio 34 or 32 and 33 with 4.33 diff ratios other wise use first and short shift to second

  • 2 months later...

^^ how i launched afew weeks back, although only took it to 6800rpm to launch, finding the friction point then riding out gets best traction and 60ft times too

gonna try 7000-7500rpm next time and see what difference it makes

what sort of tyre pressures did you run XKLABA ?

street tyres ( 265/35/18) I run 30 psi, you need the pressure to keep the centre of the tyre flat on the ground with even pressure across the tread and since the side walls of low profile tyres don't twist/flex there is no advantage to lowering the pressures, all it does is make the side walls take the weight and reduce the grip in the middle of the tyre

Drag tyres, ( 255/50/16 Toyo TQs ) 18-20psi, opposite of the street tyre reasoning

bahaha, standard ratio R33 GTR, use first and short shift into second, even with stock turbos that get 19psi by 2800rpm it's hard to keep it on boost on a second gear launch, so much so I don't even try it anymore and I reeeaaally hate clutchs

best last night for me was 11.3sec again, but this time with a 127.5mph....7500rpm clutch slip seemed to work good and not bog down....traction was abit of an issue though :/

going drags is getting addictive

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Agreed, I've never seen a 260RS specific manual. As GTSBoy said it will mostly be stagea other than the engine loom https://www.hgeconsulting.com.au/stageaservicemanual.pdf
    • You'lll likely have to make do with R33 GTR for engine/tranny stuff, and Stagea for the body. I don't know that there's even been an actual diagram seen in the wild.
    • Haha, i kow right? Could have bought so many cars for the same amount of money (or less) but driving Unicorn gives you at least +1mln to style 😅. Like wise man said "life's to short to drink cheap wine and drive boring cars" 😉
    • Newbie here, proud owner of an Autech 260RS. I'm on the hunt for wiring diagrams specific to the 260RS, particularly S1. I've ran my eyes through R33, R34 Diagrams, there are some similarities, however continue to find incorrect wire colours and pins on connectors in the 33,34 diagrams.   I was hoping someone could point me in the right direction? I'd be happy to pay for the originals in Japanese. I can translate them, at least they would be accurate.   Any help please would be greatly appreciated, never heard an RB26DETT before let alone driven one, and I've got a spaghetti monster of goodness to sort out.   Cheers Benny  
    • Hey all  im wondering if you can help me please I have put a rb20 box in my r34 gtt as my auto packed up and a friend had a spare box I know it’s not ideal but it will get me up and running for now. we have done the conversation and everything is working great but my Speedo we got a s13 speed sensor but my Speedo reads double now and I bought a speed converter but still not having any luck.  so I thought I’ll reach out and pick your brains  any help would be appreciated please as I wanna drive my car again 
×
×
  • Create New...