Jump to content
SAU Community

Fs-16" Sparco Wheels And Other Stuff

Anfanee

By Anfanee,
in Australian Capital Territory

 Share

Recommended Posts

Anfanee Grand Master

Anfanee

Posted
Posted

Hey guys im looking to sell that set of Sparco? wheels they are in decent condition only 1 seems to have guttered. they are a bit dirty been sitting in my garage for months. 2 of the rims have got decent rubber on them 2 of them rubber is stuffed.

they are 16x8 looking for $150.

Also selling that nismo steering wheel want $50 ONO for that (includes boss kit)

Also got some bright blue seat covers that someone can have for free if they come pick them up.

ALSO i know this isn't the place but im selling 1 160gb PS3 (used 1 time) and 2 wii consoles.

Ps3 $250+7 games, assas creed revalation $50

WII $70, Wii fit $50 (with board)

im an ex EB manager so i got all the games and stuff for free.

PM me if you want any of it.

post-92069-0-55321000-1331096988_thumb.jpg

post-92069-0-70011200-1331097019_thumb.jpg

post-92069-0-38836200-1331097146_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/393998-fs-16-sparco-wheels-and-other-stuff/
Share on other sites
Anfanee Grand Master

Anfanee

Posted
  • Author
Posted

Wheels gone, still got the steering wheel and those lovely? seat covers, can take a photo if you want. also all consoles still here.

Also got a question, does anyone know how much a full set of original floor mats for an R32 GT-R go for these days?

Factory 5 Mentor

Factory 5

Posted
Posted

My mate had the exact same wheels on his R31, needed 10mm spacers on rear, and 5mm on the front to clear the spring seat.... But coilovers are a good solution for that!

I'll take the Nismo wheel, might suit my HR30 Coupe nicely...

PM me you contact details (I'll be back from training on Sunday next week...)

Sinista32 Grand Master

Sinista32

Posted
Posted

R32 GTR original full set of mats (5) - yeah I can do that. They'll need a steam clean but in good nick for 22yo's.

A full set new you will need to sell your woman for them.

Nismo for the R32 GTR about $400 from memory. maybe a bit less.

PSIII you say - hmmmm

Anthony or Anne Fanny (j/ks) :D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Mistakes were made, my R34 Story

      By MBS206 · Posted

      The oil pressure sensor for logging, does it happen to be the one that was slowly breaking out of the oil block? If it is,I would be ignoring your logs. You had a leak at the sensor which would mean it can't read accurately. It's a small hole at the sensor, and you had a small hole just before it, meaning you could have lost significant pressure reading.   As for brakes, if it's just fluid getting old, you won't necessarily end up with air sitting in the line. Bleed a shit tonne of fluid through so you effectively replace it and go again. Oh and, pay close attention to the pressure gauge while on track!
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      I don't know it is due to that. It could just be due to load on track being more than a dyno. But it would be nice to rule it out. We're talking a fraction of a second of pulling ~1 degree of timing. So it's not a lot, but I'd rather it be 0... Thicker oil isn't really a "bandaid" if it's oil that is going to run at 125C, is it? It will be thicker at 100 and thus at 125, where the 40 weight may not be as thick as one may like for that use. I already have a big pump that has been ported. They (They in this instance being the guy that built my heads) port them so they flow more at lower RPM but have a bypass spring that I believe is ~70psi. I have seen 70psi of oil pressure up top in the past, before I knew I had this leak. I have a 25 row oil cooler that takes up all the space in the driver side guard. It is interesting that GM themselves recommend 0-30 oil for their Vette applications. Unless you take it to the track where the official word is to put 20-50w oil in there, then take that back out after your track day is done and return to 0-30.
    • PranK
      My new to me M35 Stagea wagon

      By PranK · Posted

      Nice, looks great. Nice work getting the factory parts also. Never know when you'll need them.
    • Chupapy
      New r33 owner

      By Chupapy · Posted

      Thanks @jtha7 I will have a look around tomorrow but it is a prick of a spot. These are some photos i tried taking 
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      I take it that the knock retard is from bearings tapping a little tune? Thicker oil is a fragile bandaid. You need a much bigger oil cooler and probably the bigger pump being discussed.
×
×
  • Create New...