Jump to content
SAU Community

Recommended Posts

Cos it was NSW, you cant sent a letter of dispute to be reviewed like here in the ACT. I've tried before. You can go to court for it, and plead your case - still paying basic court costs, or you can pay the fine.

*edit* I was advised if take it to court, the judge will look at your driving history and other credentials, and there is a chance you may have your fines RAISED rather than removed.

Edited by J'son

if this one of 31 i would have just tex-screwed on to the bumper. lol

who cares if you have to drill a hole? the number covers up everything anyway. Certainly not an excuse for not attaching a plate for 4years...

Dispaying a number plate on the dash inside a high performance car is just asking for trouble IMO. Just buy a thin number plate from the motor registry and display it like I do on my R33 GTR S1 (see pic). As for the fine - I would probably just cop it and never do it again (lesson learnt). Do you really want the hassle of going to court and running the high risk of losing and then having to pay all the court costs and the original fine? Ten years time you're not going to care about any of this lol move on

post-79200-0-51118600-1331861911_thumb.jpg

Some 3M double sided tape will hold the plate on just fine. I had my GTSTs parte held on in the same spotas the above pic with double sided tape for over 2 years.just get the plastic ones made up without hoes drilled

option 1 - pay the damn fine

option 2 - pay the damn fine

option 3 - pay the damn fine and stop complaining

In terms of mounting the plate, get two pieces of metal, bend them into an "L" shape, drill holes on the bottom and the top, screw the bottom underneath the front bar and the plate to the metal. Offset it on the left or right of the front bar.

There's a boat load of adr's and shit that number plates need to comply to. Like must be parallel to the road, visible from X angle either side of the the car at Y distance from front and rear. Plate must be RTA issue and not made by ya mate at the sign shop (rapid now pick up on fake plates). Plate must be up right also not lying on your dash or on your massive fiberglass front air dam. They sell "drift spec" off centre plate brackets you screw under the edge of your bumper where you dont see, get one.

Edited by RS4-S

^ ^ ^ exactly.

In which case, the only way IMHO that you can get off is for a psychologist's report that can convince the judge that you suffer from a rare condition, "number-plate-on-front-bar phobia" or perhaps, "number-plate-on-dashboard obsession"

And just in case you are convinced that the above are suddenly plausible, it means that you're simply looking for a loophole.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So, I've had my V36 for about a month now and have already copped an "excessive exhaust noise" notification from QLD TMR, reported by someone in my local area. It's a twin as per the original, and can have a bit of a throaty note to it when idling cold 😄 and if I do get up it a bit, it can be noisy, but it did pass a roadworthy inspection before sale, so.... ... but in the interest of being a good neighbour, I do want to quieten it down a bit. Is anyone here running a quiet aftermarket cat-back on their V36 or 370Z? And the big, bold question: does an aftermarket cat-back really make much of a performance difference on these cars?
    • The wiring diagram for the R33 RB25 is freely available, and is essentially the same same as most other RBs (just with differences as to which pin # does which job). To get the ECU to power up, you just need to provide power to the ECCS relay, and have the other power feeds that come in from the top left of the wiring diagram (wrt the ECU) that give perma power to the fuel pump relay, the ECU itself, etc etc, all connected. When you put power on all these it will just come to life. It's pretty clear from the diagram what needs to happen. Just follow the lines from the 12V + supply stuff in the top left over towards the ECU. I've even posted snips of such diagrams (not for vanilla 25, I think for Neo and 26) to various threads here in the last few months, talking about what it takes to get the fuel pump and FPCM up and going. Search these up and they will help get you started on doing the same with the vanilla 25 diagram. Hell, for all I know, I've done the same with that one in years past and have forgotten.
    • Yep...so unless someone posts up the answer you will need to probe from the ECU connector to the dash plug with a multi meter in continuity mode to trace the wires.  Note the ECU has multiple - and + (and across different key settings - Battery, IGN and Start) and most likely the power is fed from the connector(s) that is normally near the left hand headlight.
    • Thanks Duncan, I am actually just trying to get the Rb turning and running with the RB25DET S2 original loom itself  I am just trying to get it going outside the body and not thinking about the S15 or trying to match anything to the S15 loom at all I am only trying to see if anyone has done this and what pin they found to be the ignition trigger and ECU+/- on the dash connector, that's about it. Thanks  
    • Hi Guys, Does anyone know any aftermarket part numbers for a starter motor to suit the VQ25DET? I can find lots of alternative part number for the VQ35DE, which I assume would fit, but there is a lot of conflicting information out there. Thanks..
×
×
  • Create New...