Jump to content
SAU Community

Recommended Posts

Why don't you stop Trolling and f#$k off back to the Flat capper section. Oh sorry you in Marks thread........you'll fit here!

:P

Screen shot 2013-09-02 at 9.08.41 AM.png

How are your pink racing stripes nismo boy ?

:P

How are your pink racing stripes nismo boy ?

:P

Mate if you dont have anything to contribute to this thread f**k off hey. Dont need you or your trolling bullshit on my thread.

If we need a dickhead ill hola!

How are your pink racing stripes nismo boy ?

:P

don't have pink stripes nummers.....you need to keep up with times if your coming around here to Troll.

What you driving now, behind the keyboard tough guy! wasn't some POS POVO pack Merc supplied by you company!

There's a lot of bitchin going on in this thread, not a lot of progress. 22 pages dedicated to a 4 door, and still no turbo... :domokun:

Well if that sunkist guy the useless f**king pin head his would rack off and stop trolling the crap out of everyone. JoshM35 also doing the same thing (its not funny mate, dale is the witty one here. Primary school kids have better comebacks) it wouldnt be 22pages long.

This is my build thread page guise, the one i put little bits and pieces that i have done/achieved and bought to further my project along. If you wanna troll and act like a complete twat. Go elsewhere.

If it doesnt stop im not going to update it and yous wont see anything that happens or goes on and only a few of you will get to see it and those who dont live close wont.

Edited by Howaitonaito

Hahahahahhahahahahahahahah f**king hook line and sinker. Jeez you're a cry baby aren't ya, maybe it's the that tampon is a little to tight for ya vagina.

Just quietly, I've been around these parts a lot longer than you, if you go through your own thread, I have previously posted. Going even further back to this being a "build thread", well - there is a section for that, not to mention you posting your abomination of a v35, in the Stagea section.

Was actually going to ask for more pics because I was interested in what you've done, but, judging by your attitude the 'build' quality of your car can not be better than a swagilistic hella flush person like your self's view on life.

Wasn't going to go into it, but you're wayyyy to easy.

Cheer up pumpkin

Im not a cry baby. Unless you wanna post legit questions about the build and what not get off. Simple as that and from the last few things you have posted you havent.

Your two years older than i am......that "alot longer"

I posted my "abomination" of a V35 in the stagea section because if you have ever been in the V35 section, 90% of them are idiots and wouldnt care less.

"i was actually going to ask for more pics. Because i was interested in what youve done" bullshit is as fake as a hookers smile mate, dont give me that crap.

But no worries sweetheart ill keep that in mind and hey if your nice i might blow you a kiss :-)

Edited by Howaitonaito

don't have pink stripes nummers.....you need to keep up with times if your coming around here to Troll.

What you driving now, behind the keyboard tough guy! wasn't some POS POVO pack Merc supplied by you company!

Don't make me bring out the protein shakes bro
  • Like 1

Im not a cry baby. Unless you wanna post legit questions about the build and what not get off. Simple as that and from the last few things you have posted you havent.

Your two years older than i am......that "alot longer"

I posted my "abomination" of a V35 in the stagea section because if you have ever been in the V35 section, 90% of them are idiots and wouldnt care less.

"i was actually going to ask for more pics. Because i was interested in what youve done" bullshit is as fake as a hookers smile mate, dont give me that crap.

But no worries sweetheart ill keep that in mind and hey if your nice i might blow you a kiss :-)

95% of v35 owners are idiots, then you should fit right in.

Have you taken the time to go through your thread? Noopppe, if you did, perhaps you would see that I had tried to actually answer your questions about your car. But your yolo tweeny attitude won't let you actually back up your argument about my "non informative" post's

And ofcourse I'm not going to post anything useful by your initial reaction of what I said to someone else( who I've also known for quite a while). A fly couldn't even pass your nose without you breaking into tears.

Even the people in your thread cannot take you seriously, if they did, there wouldn't be pages and pages of dribble and useless shit in here.

You also stated earlier, half the useless crap in this thread isn't the cause of yourself. Which also leaves the other half to be your uselessly posted shit. Time to practice what you preach.

Now man up, drop a vq25det in the thing, get Scott to mod the fuck out of it, wipe your eyes and get on with it.

Also, post some fucking pictures! The past 5 pages don't have any.

Remind us where your Stagea is Aaron?

Must be an epic build you're doing... :whistling:

LOL I honestly think it is sitting somewhere in traralgon rusting because the guy that blew it up hasn't yet fixed it.

So wait; you don't actually have a Stagea, yet you're bagging a guy who's actually Stagea'ising his car?

I am confuse; do you even Nissan?

Yeh. Times are fun.

I wish I nissaned. I wish I still stagea'd to be honest. Had a dream that Scott gave me another Stagea. That was great.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • So, that is it! It is a pretty expensive process with the ATF costing 50-100 per 5 litres, and a mechanic will probably charge plenty because they don't want to do it. Still, considering how dirty my fluid was at 120,000klm I think it would be worth doing more like every 80,000 to keep the trans happy, they are very expensive to replace. The job is not that hard if you have the specialist tools so you can save a bit of money and do it yourself!
    • OK, onto filling. So I don't really have any pics, but will describe the process as best I can. The USDM workshop manual also covers it from TM-285 onwards. First, make sure the drain plug (17mm) is snug. Not too tight yet because it is coming off again. Note it does have a copper washer that you could replace or anneal (heat up with a blow torch) to seal nicely. Remove the fill plug, which has an inhex (I think it was 6mm but didn't check). Then, screw in the fill fitting, making sure it has a suitable o-ring (mine came without but I think it is meant to be supplied). It is important that you only screw it in hand tight. I didn't get a good pic of it, but the fill plug leads to a tube about 70mm long inside the transmission. This sets the factory level for fluid in the trans (above the join line for the pan!) and will take about 3l to fill. You then need to connect your fluid pump to the fitting via a hose, and pump in whatever amount of fluid you removed (maybe 3 litres, in my case 7 litres). If you put in more than 3l, it will spill out when you remove the fitting, so do quickly and with a drain pan underneath. Once you have pumped in the required amount of clean ATF, you start the engine and run it for 3 minutes to let the fluid circulate. Don't run it longer and if possible check the fluid temp is under 40oC (Ecutek shows Auto Trans Fluid temp now, or you could use an infrared temp gun on the bottom of the pan). The manual stresses the bit about fluid temperature because it expands when hot an might result in an underfil. So from here, the factory manual says to do the "spill and fill" again, and I did. That is, put an oil pan under the drain plug and undo it with a 17mm spanner, then watch your expensive fluid fall back out again, you should get about 3 litres.  Then, put the drain plug back in, pump 3 litres back in through the fill plug with the fitting and pump, disconnect the fill fitting and replace the fill plug, start the car and run for another 3 minutes (making sure the temp is still under 40oC). The manual then asks for a 3rd "spill and fill" just like above. I also did that and so had put 13l in by now.  This time they want you to keep the engine running and run the transmission through R and D (I hope the wheels are still off the ground!) for a while, and allow the trans temp to get to 40oC, then engine off. Finally, back under the car and undo the fill plug to let the overfill drain out; it will stop running when fluid is at the top of the levelling tube. According to the factory, that is job done! Post that, I reconnected the fill fitting and pumped in an extra 0.5l. AMS says 1.5l overfill is safe, but I started with less to see how it goes, I will add another 1.0 litres later if I'm still not happy with the hot shifts.
    • OK, so regardless of whether you did Step 1 - Spill Step 2 - Trans pan removal Step 3 - TCM removal we are on to the clean and refill. First, have a good look at the oil pan. While you might see dirty oil and some carbony build up (I did), what you don't want to see is any metal particles on the magnets, or sparkles in the oil (thankfully not). Give it all a good clean, particularly the magnets, and put the new gasket on if you have one (or, just cross your fingers) Replacement of the Valve body (if you removed it) is the "reverse of assembly". Thread the electrical socket back up through the trans case, hold the valve body up and put in the bolts you removed, with the correct lengths in the correct locations Torque for the bolts in 8Nm only so I hope you have that torque wrench handy (it feels really loose). Plug the output speed sensor back in and clip the wiring into the 2 clips, replace the spring clip on the TCM socket and plug it back into the car loom. For the pan, the workshop manual states the following order: Again, the torque is 8Nm only.
    • One other thing to mention from my car before we reassemble and refill. Per that earlier diagram,   There should be 2x B length (40mm) and 6x C length (54mm). So I had incorrectly removed one extra bolt, which I assume was 40mm, but even so I have 4x B and 5x C.  Either, the factory made an assembly error (very unlikely), or someone had been in there before me. I vote for the latter because the TCM part number doesn't match my build date, I suspect the TCM was changed under warranty. This indeed led to much unbolting, rebolting, checking, measuring and swearing under the car.... In the end I left out 1x B bolt and put in a 54mm M6 bolt I already had to make sure it was all correct
    • A couple of notes about the TCM. Firstly, it is integrated into the valve body. If you need to replace the TCM for any reason you are following the procedure above The seppos say these fail all the time. I haven't seen or heard of one on here or locally, but that doesn't mean it can't happen. Finally, Ecutek are now offering tuning for the 7 speed TCM. It is basically like ECU tuning in that you have to buy a license for the computer, and then known parameters can be reset. This is all very new and at the moment they are focussing on more aggressive gear holding in sports or sports+ mode, 2 gear launches for drag racing etc. It doesn't seem to affect shift speed like you can on some transmissions. Importantly for me, by having controllable shift points you can now raise the shift point as well as the ECU rev limit, together allowing it to rev a little higher when that is useful. In manual mode, my car shifts up automatically regardless of what I do which is good (because I don't have to worry about it) but bad (because I can't choose to rev a little higher when convenient).  TCMs can only be tuned from late 2016 onwards, and mine is apparently not one of those although the car build date was August 2016 (presumably a batch of ADM cars were done together, so this will probably be the situation for most ADM cars). No idea about JDM cars, and I'm looking into importing a later model valve body I can swap in. This is the top of my TCM A couple of numbers but no part number. Amayama can't find my specific car but it does say the following for Asia-RHD (interestingly, all out of stock....): So it looks like programable TCM are probably post September 2018 for "Asia RHD". When I read my part number out from Ecutek it was 31705-75X6D which did not match Amayama for my build date (Aug-2016)
×
×
  • Create New...