Jump to content
SAU Community

Recommended Posts

Anything is possible but it's highly unlikely..

Your pump should turn off before that happens and fuel will not pass through the reg the wrong way anyway..

You have another issue, you need to find it

Pull your I injector rail out, turn ignition to on and see if fuel comes out of the injectors..cause it shouldn't.

If it does I'm confused why it is doin it..would seem something is wired up wrong or could be as simple as a setting in your ecu..

Reading your other thread that states you have a 26 pfc and a 25 loom (or whatever the f**k you have done) it seems obvious you have muffed something up and your injectors are getting voltage full time..

disconnect fuel pump and test injectors with a multimeter or even just a test light.

Then when you realize this is the problem figure out why....

That should be fun. :devil:

I have a 26 loom and a guy on here used the original 25 loom to make it compaitble with the other stuff, installed injector dropping resistor an all that. anyway have come to the conclusion this is not common and somthing is way effed up and I shall pay a professional to fix my problems :rofl:

Injectors have constant ignition power or 12v at injector with ingition turned on & They earth through ECU.

So put test light on positive battery terminal and check for earth at injector plug, If earthed you have problem!

After Fixing problem, Drain the oil, crank out cylinders, refill with clean oil, add 20-50ml oil to each cylinder, crank over till oil pressure then start.

At least it'll flush the sh#t out after rebuild!

Edited by 32TAXI

Or a stuffed reg can do this, pull vacuum hose off the reg and see if fuel comes out.

Could make sense, if its running out of a busted reg, it'll run into the plenum, and therefor into the cylinders...

The injectors were plugged in with cas disconnected i assume they are stuck open or receiving voltage

sounds like a wiring issue as the injectors wont leak unless they are opened via ecu. what ecu?

Status tuning ever heard of pfc doing this? i have an old R32 Gtr mines computer at home (no idea whats on it) so im gonna plug that in and see if it happens again and that will diagnose what is the problem immediately

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
    • 310mm rotors will be avilable from Australia, Japan, and probably a few other places. Nothing for the front can be put on the back.
    • The filter only filters down to a specific size. Add to that, the filter is AFTER the pump. So it means everything starts breaking your pump even if its being filtered out.
    • Just like in being 14mm too small (296mm) makes it not fit, being 14mm too big (324mm) it also won't fit. You want to find the correct rotor.
    • @GTSBoy Ok so that was the shops problem...they showed R33 rotors on R34 page and i did not know 296 do not fit(and are for R33) Yes i bought "kit" with rotors and pads. Pads are ok(i have GTT calipers front and rear). They have some 324mm but no 310mm. So i dont know if they would fit. I have 17inch LMGT4s So another question. Can i fit those in the rear or they are just "too" big for that?
×
×
  • Create New...