Jump to content
SAU Community

Recommended Posts

take the fuel inlet hose off the engine. turn the car on and see if fuel comes out. also how sure are you there is fuel in the car. i work for racv and you would be supprised by the amount of times we have gone out to a car that the customer thought the fuel pump had died and.the swear they only.just put fuel in it only to get it back to the shop, pull out the pump and find an empty tank. next thing would be to check you afm. im sure someone on here could provide you with the voltages at the plug or if you know some with the same car see if you can borrow it

Link to comment
https://www.sau.com.au/forums/topic/396433-not-running/#findComment-6304078
Share on other sites

sorry for the lack of info

soooooo got some tools and done some basic tests..

fuel ok

fuel pressure ok

injector pulse ok

spark ok

even got the injectors flowed and tested just to make sure the wernt blocked

checked to see if the cat had failed and was blocking

problem is still occuring which leads me to belive its an electical problem

any ideas??

if it was the maf it would still run with a lilimt of 2500rpm becoz its in safty mode??

Edited by Benny123r33
Link to comment
https://www.sau.com.au/forums/topic/396433-not-running/#findComment-6310461
Share on other sites

an

take the fuel inlet hose off the engine. turn the car on and see if fuel comes out. also how sure are you there is fuel in the car. i work for racv and you would be supprised by the amount of times we have gone out to a car that the customer thought the fuel pump had died and.the swear they only.just put fuel in it only to get it back to the shop, pull out the pump and find an empty tank. next thing would be to check you afm. im sure someone on here could provide you with the voltages at the plug or if you know some with the same car see if you can borrow it

soooooo got some tools and done some basic tests..

fuel ok

fuel pressure ok

injector pulse ok

spark ok

even got the injectors flowed and tested just to make sure the wernt blocked

checked to see if the cat had failed and was blocking

problem is still occuring which leads me to belive its an electical problem

any ideas??

if it was the maf it would still run with a lilimt of 2500rpm becoz its in safty mode??

Link to comment
https://www.sau.com.au/forums/topic/396433-not-running/#findComment-6310471
Share on other sites

an

soooooo got some tools and done some basic tests..

fuel ok

fuel pressure ok

injector pulse ok

spark ok

even got the injectors flowed and tested just to make sure the wernt blocked

checked to see if the cat had failed and was blocking

problem is still occuring which leads me to belive its an electical problem

any ideas??

if it was the maf it would still run with a lilimt of 2500rpm becoz its in safty mode??

Unplug the afm and start the car. Doubt it's the problem though.

Link to comment
https://www.sau.com.au/forums/topic/396433-not-running/#findComment-6310592
Share on other sites

  • 3 weeks later...

Get a stand alone ecu.

None of this piggy back bs

bingo.

So, the usual advice. Do some research on who are the tuners in your area (you dont want to drive 2hrs + just to drop a car off for tuning of if any troubleshooting is required afterwards) and then work out who is the best and what is their prefferred platform. Of course cost is an issue but you usually get what you pay for and a bad tune = the need for a new motor = prob not worth skimping $200 for the cheaper tuner... In a similar vein, avoid Mine's tuned ECU's. not going into why here.

General consensus is that PowerFC or Z32+nistune is the way to go. Take into account whether having an aftermarket computer puts you in easy defect territory too (if so- nistune)

Link to comment
https://www.sau.com.au/forums/topic/396433-not-running/#findComment-6339786
Share on other sites

  • 5 weeks later...

Hi All,

I'm a noob so I'm not sure if I'm on the right thread or not, but here goes..

Last night I did the mod where you ground out the boost solenoid on an R33GTSt.

Well I read the entire thread on that before attempting it, & then did it as specified.

When I went to test it on my way to work this morning it would not rev over 2500rpm, just kept coughing until i dropped the revs below 2500.

I freaked out (i only just got the car), & put it back to standard, but it still wont rev over 2500rpm..

Have I broken something? Can I fix this?

So far I have reset the ECU as specified (disconnect batt & pump brakes)

I hot wired the solenoid to see if it works (it does)

& I tried running the car with the solenoid grounded & ungrounded.

Still only 2500 rpm..

Please HELP!!!

Link to comment
https://www.sau.com.au/forums/topic/396433-not-running/#findComment-6380612
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Nah its a server spammer thing  Although, now that I manually approve all the accounts I can probably loosen up some of the restrictions.  
    • Thread bump, again! Although, no bad news this time. Posting for the sake of possible root cause. Basically, I rebuilt it (mostly stock), installed Haltech + sensors, had it running fine on new ECU.  Still not really understanding why it cracked pistons last time. Got to tuners, and while checking timing, noticed +-10deg of timing scatter while revving. Changed CAS, and it was rock solid. While not definitive, can't imagine seeing 20+ psi with that amount of scatter would be a good thing. Also glad I found something.   Bit more of a run down; Carried out a stock rebuild, a set of stock pistons, out of a spare bottom end. Everything stock apart from head studs and oil restrictors. (so I can pretend I didn't let the Nissan out, ha.) Armed with the measuring gear and FSM, set about doing overhaul. Oil restrictors as per oil control thread for a RB25, stock oil pump, drifting. Head drain/vent from rear of head, to passenger side of sump above oil level. Two dash 10 vent lines from drivers side of sump (unused atm) Hi octane style cam cover breather kit Splash covers over last 2 cam caps. Both breather lines from cam covers to vented to atmosphere catch can, not plumbed back into sump (wanted to see what it was actually breathing). Got it run in (did about a 1000km) no to low boost scenario, As I had questions over old ECU setup. Installed haltech +sensors for flex Retune on E85 (finding CAS Issue along the way), made 300rwkw at 20psi, out of wastegate. Did a drift day the next day (yes, it was a big weekend!) and was checking catch can throughout the day, ZERO blowby. I mean nothing. Lines from cam covers are not even wet. Done a bunch of street driving, spirited and catch can is still dry. Early days I guess, but pretty happy so far. Also now run 10w60, up from the 10w40 that I used to run. Oil pressure is significantly better, especially when hot (as you would expect)      
    • Thanks buddy. I thought it was a server storage thing. 🤣
    • Perfect! Thanks for this, both look like great options!
×
×
  • Create New...