Jump to content
SAU Community

Recommended Posts

all he did was changed oil, oil filter and few minor things that dont contribute to motor, when you put your foot into it, it has power until about 3,000rpm then starts losing boost but picks up again and then cuts out again, its constant throughout the rev range

all he did was changed oil, oil filter and few minor things that dont contribute to motor, when you put your foot into it, it has power until about 3,000rpm then starts losing boost but picks up again and then cuts out again, its constant throughout the rev range

Could be any number of things from bad fuel, to coil packs to air flow meter to vacuum leak... Very hard to say based on the information you've provided. E-Mechanic isn't an easy occupation.

Did the mechanic do your fuel filter? Does the car seem like it's running rich at all, any black smoke coming out the exhaust when these surges occur? Does it idle nicely?

idles fine and only run 98oct fuel, no smoke at all and i cant remember if he did fuel filter, its the mrs car and the receipt is in her car. it doesnt seem to run rich whatsoever, what oil is best to run in the neo's?

Get that receipt, list everything done. Then we might actually be able to help.

RB oil filter changes are notorious for being a complete pain in the ass, a careless mechanic can easily damage a vacuum hose causing the motor to overboost and hit R&R.

ok heres what was done

-change oil and oil filter

-check brakes

-top up fluids

-check lights steering tyres suspension etc

-inspect underbody, hoses, belts etc

the oil that was put in is 10w-40 semi synthetic mobil formula

ok heres what was done

-change oil and oil filter

-check brakes

-top up fluids

-check lights steering tyres suspension etc

-inspect underbody, hoses, belts etc

the oil that was put in is 10w-40 semi synthetic mobil formula

This sounds like your issue. I bet he has played around with some hoses and not noticed has has pulled one off or he has replaced one and not put a clamp back on, etc etc. I would just go over all your hoses, and I mean all of them. Unfortunately it's not a fun job on a Neo confused.gif

As for oil, I personally always use full synthetic as well but it's not realllllly critical. Semi-synthetic will do the job.

This sounds like your issue. I bet he has played around with some hoses and not noticed has has pulled one off or he has replaced one and not put a clamp back on, etc etc. I would just go over all your hoses, and I mean all of them. Unfortunately it's not a fun job on a Neo confused.gif

As for oil, I personally always use full synthetic as well but it's not realllllly critical. Semi-synthetic will do the job.

ok will check it all out tomorrow thanks alot guys :)

  • 3 months later...

Did you find out what the issue was? I have a similar problem except mine surges between 4000 & 5000 RPM & then pulls fine from there to redline. It only happens when my foot is flat not at part throttle.

Did you find out what the issue was? I have a similar problem except mine surges between 4000 & 5000 RPM & then pulls fine from there to redline. It only happens when my foot is flat not at part throttle.

That sounds like RnR to me. Cold weather, possibly running a touch more boost and maxxing out your AFM.

I thought it might be R&R. It doesn't have a boost controller on it so should be running stock boost although the boost gauge shows about 0.7 bar.

I reset the ECU & also changed the BOV so it was re-circulating again & it seemed to almost fix the problem, now its just a slight hesitation at 4500rpm only sometimes, other times its fine.

The re-circulating pipe isn't 100% sealed so I will seal it all up & see if that fixes it.

unless the mechanic is a complete berk then he shouldnt of knocked any vacuum hoses off when changing the oil (at least)engine bay is large and oil filter easy to get to when compared to a 32 anyway

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Not sure the US can import anything other than the C34 Stagea's, but if you can and you need to to tow, DO NOT under any circumstances get an M35 Stagea. If it is just as a family car and your country/state allows it, absolutely and definitely get an M35 (3.5L if possible as it is effectively a 350Z) over a C34.
    • Punch your VIN (nm35-xxxxxx) into Amayama.com You can see everything there quite easily.
    • Thanks for that, I'll check it all out. I can always do the brakes last anyway if its a problem.  The 16's are super cool, if they do fit I'll cruise around with them for a bit.  
    • Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
×
×
  • Create New...