Jump to content
SAU Community

Recommended Posts

  • Replies 7.5k
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

^^^^ Erin sold the 32!!!!! *sits back stunned*

Is a hawt car, she is a very lucky girl :wave:

post-4594-1153047821.jpg

post-4594-1153047886.jpg

yep we finaly sold her.....been gone for a week now :D we have lost a memberof our family.... :O had to so we could buy our new bussiness tho, down in the new section of collonades. we will be back in a year or so with bigger and better thing tho....350z styals!

heard she might have been defected alredy..... : not good, poor thing!

Edited by moo_r32

I always see a maroon r33 at work (Ozroll pty ltd), it in the parking lot and its always parked next to a white supra. Im driving the black s13 silvia. Never see the owner cause its always there before me and always there when I leave.

yep we finaly sold her.....been gone for a week now :P we have lost a memberof our family.... :O had to so we could buy our new bussiness tho, down in the new section of collonades. we will be back in a year or so with bigger and better thing tho....350z styals!

heard she might have been defected alredy..... : not good, poor thing!

yep, flick got defected 2 nights ago up in valley view. too low, to wide a track, amongst other things. got pulled over next morning as well on way to work (got given 72 hours to drive car).

another to add.

same white 33 i've spotted a few times now, white 3 spoke rims.

nice exits from certain spot in the city....baaaad move coming back tho....half hour or watching an he was still being reamed by cops who went onto wrong side of road to stop him......ouch.

yah that's west terrace lol. i can't imagine they were gonna be letting him move anytime for couple of hours...they gotta outta the cop car screaming at him to get the f**k outta the car n shit.. :S

Hahaha.. I was there walking to my car after having a nice supper from hungry jacks (west terrace). And suddenly heard a roaring RB25 sound on the shell exit way - the white R33 was making a nice "Takashi (DK)" move on west terrace. A minute later, the poor 'line' was busted by the blue boys on the opposite site of the road. I hope he didn't get any pick slips for doing that.

Didn't know why he was caught thou cause the cops were coming from the opposite lane. I guess he must had done an illegal U-turn at the traffic lights.

saw a grey 34coupe race a VS/VR? commodore today at the South Rd Aylifes road intersection. They were about even when i was going past.

so u drove straight past a couple of racers :D WOW u must have teh power :wave:

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
×
×
  • Create New...