Jump to content
SAU Community

Recommended Posts

Hope this is the right area.

Was on gumtree this morning looking for skylines as usual, and there must've been a shipment of imports because there was a few skylines and evos uploaded from wangara (car shop suburb for all you non WA people)

I did find a two stock R34s which I was so happy to see. however the manual was 18k and the Auto was 11k :(

This seems way to expensive, are they overcharging? Because if I could get that auto cheap I'd just do an Auto to manual conversion with an r33 gearbox and follow an old thread I found on here :)

So what is the currrent value for auto and manual R34s (stock) that you guys think?

Link to comment
https://www.sau.com.au/forums/topic/397491-value-of-auto-r34-gtt/
Share on other sites

labour isnt really a problem, dad rebuilt a few cars, I'm not afraid to get my hands dirty, and cousin owns a repair shop with a hoist. And I'm not looking to increase the value. I just hate auto's with a passion :)

ok a few things, there will be a big difference in the value of cars that are the same. you may get 2 r34's, both manual, etc that are vastly different in price. a lot of this will come down to general condition of the car. some will also come down to one owner being more eager to sell his car than the other.

as for the auto vs manual price difference, there will always be a difference in price. the 18k manual one is at the upper end of the price range. you will certainly find cheaper ones around. unless you could get the auto for a lot less than 11k i wouldn't bother doing a conversion. for starters, parts will cost you a few thousand dollars to do it properly. will still cost you a few grand to do a half arse job. then there is all the dicking around with getting the wiring sorted so that the ecu uses the right maps (most people don't do this).

i would also say the same thing about importing a car vs buying locally. don't bother importing. buy locally. that way you can personally go and inspect the car, take it for a drive and see what it's like. you can inspect the body, listen to the engine and get a general feel for what sort of condition it's in rather than just taking someone elses word for it.

you may also want to do plenty of research of running costs and maintainence costs of a turbo car before you get too far in the process. things like how expensive insurance will be (a lot for a young driver), running it on premium unleaded, regular oil changes, etc. plus the cost of fixing common problems such as failing coil packs. they aren't for everyone.

yeh I am, I dont get why there's such a huge price jump from R33s to R34s... There was a gtst R33 for $3500 on carsales in FEB that I saw.

Basic Rule:- Production Numbers of the R34 were much less than the R33 > Join the dots.

BTW, welcome to SAU

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ha, well, it's been.... a bit of a journey. Things have taken much longer than I'd hoped. I'll probably put up a thread at some stage. Hopefully soon. The car's not done any kms since my update in June though, put it that way.
    • Here's the chart for fuel pressure vs. current draw, assuming your base fuel pressure is 3 bar and you run like 0.5bar boost on WOT, you should only momentarily hit 9amps here and there. (Ignore my prev post, I cannot read a chart these days it seems)
    • Those comp test results are not hideous. Whether they are accurate or not (ie, when that comp tester says 140 psi, is the real pressure120, 140 or 160?) is unknown to us. The state of the battery used to crank it over is unknown, etc etc. Many people around here would say that the absolute values and the spread are perfectly fine to just add boost and keep going. I personally would be happier with a narrower spread than that, but even the diff between 125 and 145 is not terrible. That one cylinder at 125 though, has probably copped some damage relative to the others. You should inspect the valves seeing as you've got it open. Do you know how to measure installed ring gaps? That, and an inspection of the rings themselves, is how you will determine whether they need to be replaced. If you're not good to do these things, take the block and the pistons and rings to a shop that is, and ask them for the go/no-go on them. Do the bores need a hone at all? If so, you might well be justified in getting some different pistons in order to get away from the ring supply problem. Whether you're happy to spend a lot more money right now, on more gear, rather than less money, but an amount that looks stupid given that you will only get a handful of rings in exchange for that money, is for you to decide.
    • also possibly backed up to my filler and shat down it! 🤣
    • Ok so i would love some advice here please, i purchased an R33 a few months back and its had a few mods done to the engine, its an RB25det running a Master ECU, 1200cc injectors, bigger turbo, oil cooler, oil filter relocation kit, Spool H-beam rods, acl/ross pistons. When i removed the motor from the vehicle (as its getting a respray) i thought i would compression test it and these are the following results. Cylinder 1-145psi, Cylinder 2-143psi, Cylinder 3-125psi, Cylinder 4-145psi, Cylinder 5-140psi, Cylinder 6-135psi this test was done with the motor on the ground and powering up the starter motor. I dropped the sump and found broken oil squirters on cylinder 3,5 and 6. I was told my rings are probably worn so i stripped the motor completely to get a new set of rings for it. The trouble is no one has these rings anywhere and they have to be custom made by Ross over in the states and will cost about $600+$200 delivery. My question is how can i tell if my rings are at fault and if they are still ok and is this price ok for a set of rings?
×
×
  • Create New...