Jump to content
SAU Community

Recommended Posts

R32 Nissan Skyline GTR 1989 imported by me in 2004. $13,500 or reasonable offer.

Complied in the ACT.

I dont get the time to drive it, would like to see it go to a good home.
Located in Canberra but will trailer deliver to you for cost of fuel + hire.
Last rego inspection:
- Back left handbrake was not applying full force.
- One of the engine mounts is split, don't know how long it was like it, never had an issue before, I bought a spare, haven't fitted it.
- Clear is coming off.
Needs a tune, throttle bodies need balancing. I cant afford to get it done.
Steel wheel ball bearing turbos built by Croydon Motorsport, all the under plenum pipes were checked and replaced because the last mechanic overtightened the water bleed screw and it sheared, so when I changed the water pump I couldn't bleed it, had to dismantle the entire inlet side to fix it. Found the paper gaskets blown in two places so put in HKS metal gaskets.
Had the injectors serviced, removed the fuel tank and cleaned the lines out, new fuel lines as well. new timing belt went in a while ago.
Cat back exhaust, HKS Pods, everything else is stock.

post-8901-0-44925300-1396592995_thumb.jpg

post-8901-0-86222700-1396593012_thumb.jpg

post-8901-0-35605200-1396593029_thumb.jpg

post-8901-0-79834200-1396593048_thumb.jpg

  • 2 weeks later...

My Gloss black GTR Bonnet

Condition is immaculate

has the heat/sound deadener and squirters

$600 (or $700 if you wish to barter)

most have seen it on my GTR or in my mancave

however if you want to drop by or need pics

Just ask

Cheers

Richard

Will also be selling off both sets of my Rays Volk GTC's soon

Gold set to suit GTS-t's (Face 2)

18 x 9 +29 ®

18 x 8 +29 (F)

4 x Federals RSR's on rims Good tread road legal

Minor rash will be fixed first

Sit hella flush on my 34 GTT

$2400

Diamond Black to suit GTR's

18 x 9.5 +15

2 x Bridgestone Potenza's RE050's (road legal tread)

Minor rash is being fixed now

Also sit flush with guards

$2400

Both sets come with Rays Nuts

- Volk CF centre caps

- Socket/s

Payment plans on Rims available if your not so flush with cashish

Interested in those Dimond Black GTCs

Hi All,

I have the following stuff to sell all pickup in Canberra / QBN.

Price is make are offer on here or via PM... My R33 is sold so no longer needed, this stuff will either be ebayed or thrown out

Stock Airbox with high performance filter... good condition

http://imgbox.com/sf**kqx1

Reverse switch (that controls the reverse lights) Brand new genuine nissan.

http://imgbox.com/xqypXZoU

Plastic Box for POD

http://imgbox.com/oFvc0G3k

Clutch and Fan. Clutch is stuffed!!

http://imgbox.com/THybj6ju

RB25det Head... great condition

http://imgbox.com/sKfHLg24

http://imgbox.com/0YnUVuNc

R33 s2 stock exhaust... all the way from dump pipe to back.. good condition

http://imgbox.com/l0c2GHWp

R33 S1 ABS pump... OK condition should work fine though never tested (i had a s2)

http://imgbox.com/eAV1Owii

R33 Stock wheels

http://imgbox.com/vM0IGwzw

http://imgbox.com/WbVGV2uA

R33 Emergency tyre

http://imgbox.com/bmxZHrPT

Hi All,

I have the following stuff to sell all pickup in Canberra / QBN.

Price is make are offer on here or via PM... My R33 is sold so no longer needed, this stuff will either be ebayed or thrown out

Stock Airbox with high performance filter... good condition

http://imgbox.com/sf**kqx1

Reverse switch (that controls the reverse lights) Brand new genuine nissan.

http://imgbox.com/xqypXZoU

Plastic Box for POD

http://imgbox.com/oFvc0G3k

Clutch and Fan. Clutch is stuffed!!

http://imgbox.com/THybj6ju

RB25det Head... great condition

http://imgbox.com/sKfHLg24

http://imgbox.com/0YnUVuNc

R33 s2 stock exhaust... all the way from dump pipe to back.. good condition

http://imgbox.com/l0c2GHWp

R33 S1 ABS pump... OK condition should work fine though never tested (i had a s2)

http://imgbox.com/eAV1Owii

R33 Stock wheels

http://imgbox.com/vM0IGwzw

http://imgbox.com/WbVGV2uA

R33 Emergency tyre

http://imgbox.com/bmxZHrPT

And this should be an rb25det block for sale above not head!!

DOWN TO $12,000 - must go.

Also has Greddy Oil Filter relocation Kit.

Just flushed radiator, fitted new battery (SuperCharge batteries are crap), just flushed and put in fresh fuel.

Pretty sure I have fixed the handbrake issue.

R32 Nissan Skyline GTR 1989 imported by me in 2004. $13,500 or reasonable offer.

Complied in the ACT.

I dont get the time to drive it, would like to see it go to a good home.
Located in Canberra but will trailer deliver to you for cost of fuel + hire.
Last rego inspection:
- Back left handbrake was not applying full force.
- One of the engine mounts is split, don't know how long it was like it, never had an issue before, I bought a spare, haven't fitted it.
- Clear is coming off.
Needs a tune. I cant afford to get it done.
Steel wheel ball bearing turbos built by Croydon Motorsport, all the under plenum pipes were checked and replaced because the last mechanic overtightened the water bleed screw and it sheared, so when I changed the water pump I couldn't bleed it, had to dismantle the entire inlet side to fix it. Found the paper gaskets blown in two places so put in HKS metal gaskets.
Had the injectors serviced, removed the fuel tank and cleaned the lines out, new fuel lines as well. new timing belt went in a while ago.
Cat back exhaust, HKS Pods, everything else is pretty much stock.
No rust.
Edited by xfixiate

1990 R32 GTR RB26DETT - $22,000 ONO - 0422626173



Up for sale is my 1990 Nissan skyline R32 GTR, It is in great condition with 84,000kms and the original japanese service books, it has been used as an occasional weekend car.



Panasport G7 C5C 3 piece wheels with Federal 595 RSR 255/45/17 (1500kms on tyres)



Greddy Type S Coilovers



Cusco rear camber arms



Cusco castor rods



HKS pod filters



Greddy Cam Gears



HKS Power FC with hand controller



New Nissan injector seal kit with new Pintle caps (installed less than 300kms ago)



HKS electronic boost controller



3.5” catback exhaust with 4” oval rear muffler (nice and quiet)



RDA slotted and dimpled rotors with Intima SR brake pads (installed less than 1000kms ago)



Genuine Nissan Tie Rod ends (installed less than 1000kms ago)



Rebuilt Drive shafts with new CV boots (installed less than 1000kms ago)



Steering Rack boots (installed less than 1000kms ago)



Rebuilt Headlight Switch (installed less than 1000kms ago)



Wheel alignment performed by Capital Steering less than 500kms ago



IMG_3751_zpse1a54a49.jpg



IMG_3722_zps079d5510.jpg



IMG_3694_zps412a236b.jpg



IMG_3711_zps190769a4.jpg



IMG_0168_zps4ec5f741.jpg



IMG_0131_zps6ee0137d.jpg


Edited by JimmyS

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
    • Sorry I meant that we are building the EH for a client.
    • LOL, when one "money pit" is never enough Noice, and excellent work mate
×
×
  • Create New...