Jump to content
SAU Community

Recommended Posts

Hi

I am about to have a full exhaust system done on my series 2, RS Four S.

Not sure at this point wether to get twin dump pipe or just a bellmouth.

I will also be getting a Blitz LM return flow intercooler installed and was wondering if I will need to have the car tuned with aftermarket ecu piggyback or maybe Nistune board.

Or will the car run fine with the standard ecu ?

Any help would be great thanx

post-93563-0-21462800-1336787141_thumb.jpg

Since you have a S2 you would benefit from getting a Nistune fitted and tuned. The car will run on the stock ecu but from stock they all run very rich and a tune will benefit economy and/or performance and help your engine live longer.

Do the exhaust and the intercooler first if you want and get the Nistune as soon as you can.

Yes if you can source an R34 GT-t PFC and run 3.7v to pin 51 on the ecu to get around traction control you can use a PFC.

If you just gut your existing cat you get the same thing for free. More power noise very slightly increased.

nistune is about $350 without the software (off the top of my head)

+ cost of tune

pfc is $1000+

+cost of tune

with an exhaust and no tune on 7psi my rs4s was making 135awkw

10psi and a nistune + tune will get you near 200awkw

a guy i know with another rs4s said the tune was the most noticable mod he has done so far

also, the cost of tuning a nistune would only be a little more than a piggyback but you will get much better results

I already have Greddy power extreme exhaust, blitz intercooler, Greddy oil catch tank, JJR bellmouth dump pipe all awaiting to be installed. I will also be getting Splitfire coil pack and from what your all saying is I need Nistune board fitted, boost controller and then a tune. What kind of power should I then expect to see ?

Hey mate, perhaps jump into the Forced Induction performance thread and have a flick through the recent pages of the RB25 dyno results. That will give you something to go off, and then you can see what to expect. With the stock turbo, people don't push too hard.

Have you bothered to read anything in your own thread? I swear this has been asked and/or answered already more than once.

And right there is the reason a lot of people don't get on these forums cause there's always someone who has to show some infant ism.

I am merely asking to clarify so as not to get told some bs from a workshop. After all isn't that what this is here for. C'mon

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
    • 310mm rotors will be avilable from Australia, Japan, and probably a few other places. Nothing for the front can be put on the back.
    • The filter only filters down to a specific size. Add to that, the filter is AFTER the pump. So it means everything starts breaking your pump even if its being filtered out.
    • Just like in being 14mm too small (296mm) makes it not fit, being 14mm too big (324mm) it also won't fit. You want to find the correct rotor.
    • @GTSBoy Ok so that was the shops problem...they showed R33 rotors on R34 page and i did not know 296 do not fit(and are for R33) Yes i bought "kit" with rotors and pads. Pads are ok(i have GTT calipers front and rear). They have some 324mm but no 310mm. So i dont know if they would fit. I have 17inch LMGT4s So another question. Can i fit those in the rear or they are just "too" big for that?
×
×
  • Create New...