Jump to content
SAU Community

Recommended Posts

Hi

I am about to have a full exhaust system done on my series 2, RS Four S.

Not sure at this point wether to get twin dump pipe or just a bellmouth.

I will also be getting a Blitz LM return flow intercooler installed and was wondering if I will need to have the car tuned with aftermarket ecu piggyback or maybe Nistune board.

Or will the car run fine with the standard ecu ?

Any help would be great thanx

post-93563-0-21462800-1336787141_thumb.jpg

Since you have a S2 you would benefit from getting a Nistune fitted and tuned. The car will run on the stock ecu but from stock they all run very rich and a tune will benefit economy and/or performance and help your engine live longer.

Do the exhaust and the intercooler first if you want and get the Nistune as soon as you can.

Yes if you can source an R34 GT-t PFC and run 3.7v to pin 51 on the ecu to get around traction control you can use a PFC.

If you just gut your existing cat you get the same thing for free. More power noise very slightly increased.

nistune is about $350 without the software (off the top of my head)

+ cost of tune

pfc is $1000+

+cost of tune

with an exhaust and no tune on 7psi my rs4s was making 135awkw

10psi and a nistune + tune will get you near 200awkw

a guy i know with another rs4s said the tune was the most noticable mod he has done so far

also, the cost of tuning a nistune would only be a little more than a piggyback but you will get much better results

I already have Greddy power extreme exhaust, blitz intercooler, Greddy oil catch tank, JJR bellmouth dump pipe all awaiting to be installed. I will also be getting Splitfire coil pack and from what your all saying is I need Nistune board fitted, boost controller and then a tune. What kind of power should I then expect to see ?

Hey mate, perhaps jump into the Forced Induction performance thread and have a flick through the recent pages of the RB25 dyno results. That will give you something to go off, and then you can see what to expect. With the stock turbo, people don't push too hard.

Have you bothered to read anything in your own thread? I swear this has been asked and/or answered already more than once.

And right there is the reason a lot of people don't get on these forums cause there's always someone who has to show some infant ism.

I am merely asking to clarify so as not to get told some bs from a workshop. After all isn't that what this is here for. C'mon

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Did you panel beat the dents or have you tried to repair this only using filler?  Is your sanding block soft/flexible and is following the shape of the panel rather then just knocking down the high points? 
    • I haven't knocked them down yet. I think I made the repair more complex than it should have been. I had rock chips combined with waviness and dents and I tackled it all in one because it was near each other and just end up wasting a bunch of bog lol. I'll knock down those areas and see how I go. And yep what you are saying at the end is correct. I think I might be sanding the top of a steep hill then my sanding block falls into the dent and gets rid of the guidecoat if that makes sense. Though shouldnt unless I'm covering too big of an area with not a long enough block. I'll try something new and provide some updates. Getting there though! Thanks as always.  
    • Yeah makes sense, hard to comment on your situation without seeing what your doing. I was talking generally before, I would not be looking to randomly create low spots with a hammer to then have to fill them.  It's hard without seeing what your doing, it sounds like you are using the guide coat to identify low spots, as you're saying the panel is still wavy. I don't see how you're not ending up with patches of guide coat remaining in a wavy panel? Once the high spots are knocked down to the correct level, surely to have a wavy panel you need low spots. And those low spots would have guide coat still in them?
    • So I'll put filler past the repair area a bit to make sure I don't miss anything. Then I'll block it until it's almost level, put the guidecoat, then keep blocking until it's gone. Then it's still wavy.  In regards to hitting the panel, I saw this video might give more context - Skip to 0:47 he knocks it down. But yeah I'm sanding until the guidecoat is gone then checking because otherwise my filler is still well above the bodyline. Unless what you're saying is I should put guidecoat around it early, surrounding the filler then stip once it's gone?
    • I refreshed the OEM injectors with the kit and connected it up. It now ideals okay even with the IACV removed. Driving still has the same cutoff issue like the 550cc injectors so the issue is somewhere else. I bought FPG's Fuel Pump Hanger. I will be installing it next, but it is not as straightforward as I thought it was with my limited wiring knowledge and no instruction on the specific model I purchased (FPG-089). I also got the incorrect billet clamp as I could not find info on the OEM sizing.
×
×
  • Create New...