Jump to content
SAU Community

Recommended Posts

This game is constantly online, so even in a private game by yourself you are dependent on a constant connection to battle.net . Because item drops, characters, etc comes from the server side congested servers or a bad connection can bugger the whole thing up. Hoping it is better when I get home tonight.

i am aware of this...but still dont like the idea.. borderlands does random drops etc without the online essential.

Have spent an hour or so playing, have gotten kicked off servers twice due to connection fall out. I guess this is now the standard when i new game is released, I am only playing single campaign though and dont completely understand why i must be connected to their server the entire time???

It is however so far a good game, the lag points though are annoying me but i would say these would get fixed as updates come to light.

only real thing i can think of is for Piracy reasons is why theyve made it like this. and i wouldnt worry, it will all get sorted out asap. (and ive only played multiplayer so far......get some friends, its fun!!)

other than the servers going down this arvo for a few hrs ive had no issues or dropouts...just the occasional jitter from lag spikes, which i assume will get sorted out anyways.

awesome game lvl23 barb, with a monk and wizzard in tow :)

  • Replies 160
  • Created
  • Last Reply

Top Posters In This Topic

So many people having troubles.

I don't even get lag :S

With or without people.

By yourself or with others, its the same game, same quests/missions. I just have mine open to others and then they join me to do the same quests.

Yeah I'm currently playing a wizard which is pretty much living up to the name glass cannon. Mass + int items and minimal +vit. I literally get one shotted by champions and bosses so I need others to be meat shields. Although I literally melt enemies away with the stupid damage done.

Awesome game.. Insanly addictive.

Lvl 23 Monk! = tough as F$&@! And majorly under estimated! Always getting massacre xp bonuses! Badly want to play tonight but gotta spend time with the misses!

Yeah i think there may have been some confusion when it first came out saying that Diablo was gfx hungry due to the stuttering, but generally that is caused through latency in the connection, not so much a graphics card.

It would surprise me if it was gfx hungry as although the visuals are nice, its not anything out of this world like crysis was at the time or MW3 for example (ok BF3 as well for you haters)

Yeah got my copy last week and so far i'm pretty happy with it, it has mostly similar to D2 in some ways, i do need a better computer its about 4yrs old to play it better so may have to invest in one soon. My internet is pretty fast and i am having a lot of trouble on the America Servers, i swapped to the Asia one there for a little bit when i had 3007 error coming up and i must say it played a lot smoother and quicker. I do to wish that they made this an offline game so i could play it when i'm away for work for the week. Overall still a kickarse game got a lvl21 Barb just playing every now and then when i get a chance.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
×
×
  • Create New...