Jump to content
SAU Community

Recommended Posts

Sorry to Hi-jack your thread but does anyone know with "street semi's" like Federal RSR's for example is there any point in warming them up at the drags or are they the same as normal street tyres that don't like heat?

Sorry to Hi-jack your thread but does anyone know with "street semi's" like Federal RSR's for example is there any point in warming them up at the drags or are they the same as normal street tyres that don't like heat?

its always good to warm up the tyres this will give you bit of extra grip , you probably seen other cars running semi or even full slick still warming them up.

its always good to warm up the tyres this will give you bit of extra grip , you probably seen other cars running semi or even full slick still warming them up.

I under stand the guys with race tyres warming them up coz race tyres only work at a certain operating temp's but street tyres are designed not to need to be warmed up to be able to produce grip & iv been told heating them can actually make things worst. So just wondering how these street semi's work.

It comes down to how much power your car is putting down and how serious you are.

Do you have a 185kw, FMIC, exhaust, filter car or a 300kw, GT3076 + supporting mods car or a 350+, forged, gt35 + all the fruit car?

If it's 185, a warm up is pointless, traction won't be an issue. If it's ~300ish then it might be of use you're running street tyres, but in reality you'll do better simply managing your throttle and clutch better. If it's the last option, then I would expect you are running slicks and intend on launching hard and a warm up burn out is definitely beneficial (if not slicks then no amount of street tyre burnout is going to stop you wheel spinning for a good portion of the race).

So, in conclusion, I'm going to bet your running moderate power on street tyres which means a pre race burnout is going to give very limited benefit. But do one anyway, cause they are fun :)

I under stand the guys with race tyres warming them up coz race tyres only work at a certain operating temp's but street tyres are designed not to need to be warmed up to be able to produce grip & iv been told heating them can actually make things worst. So just wondering how these street semi's work.

pretty sure the tyres will be warming up regardless, when doing a burn out you give the tyre the chance to grip the surface properly when taking off i own MT semi slick tyres and yes they are meant to be warmed up , those that dont properly dont have the option to, however from experience , it works.

Edited by Hiroshima Screamer

It comes down to how much power your car is putting down and how serious you are.

Do you have a 185kw, FMIC, exhaust, filter car or a 300kw, GT3076 + supporting mods car or a 350+, forged, gt35 + all the fruit car?

If it's 185, a warm up is pointless, traction won't be an issue. If it's ~300ish then it might be of use you're running street tyres, but in reality you'll do better simply managing your throttle and clutch better. If it's the last option, then I would expect you are running slicks and intend on launching hard and a warm up burn out is definitely beneficial (if not slicks then no amount of street tyre burnout is going to stop you wheel spinning for a good portion of the race).

So, in conclusion, I'm going to bet your running moderate power on street tyres which means a pre race burnout is going to give very limited benefit. But do one anyway, cause they are fun :)

you haven't been to the drags much have you? i was having traction issues with about 180hp (so about 135kw) in my magna. a mate of mine had a sr20 in a sigma and with street slicks he was lifting one of the front wheels off the ground when launching and he only had about 250hp. he was simply holding it on the rev limiter and pretty much just side stepping the clutch. his 60' times were around 1.5 seconds.

you haven't been to the drags much have you? i was having traction issues with about 180hp (so about 135kw) in my magna. a mate of mine had a sr20 in a sigma and with street slicks he was lifting one of the front wheels off the ground when launching and he only had about 250hp. he was simply holding it on the rev limiter and pretty much just side stepping the clutch. his 60' times were around 1.5 seconds.

Actually, I have.

My 33 was a typical 11psi, FMIC, exhaust and pretty healthy. I had china specials on the back and traction was never an issue. I could light up the rears in first and a tiny chip/squirm into second if I wanted, but by christ I had to be pumping it pretty friggin' hard. Pull back to 95%, which is sensible if it's your daily, and traction was not an issue.

It comes down to how much power your car is putting down and how serious you are. Do you have a 185kw, FMIC, exhaust, filter car or a 300kw, GT3076 + supporting mods car or a 350+, forged, gt35 + all the fruit car? If it's 185, a warm up is pointless, traction won't be an issue. If it's ~300ish then it might be of use you're running street tyres, but in reality you'll do better simply managing your throttle and clutch better. If it's the last option, then I would expect you are running slicks and intend on launching hard and a warm up burn out is definitely beneficial (if not slicks then no amount of street tyre burnout is going to stop you wheel spinning for a good portion of the race). So, in conclusion, I'm going to bet your running moderate power on street tyres which means a pre race burnout is going to give very limited benefit. But do one anyway, cause they are fun :)

I dono my R34 was only making 165rwkw & i was having some pretty big traction issue. Had to baby it off the line (holding it at about 3 grand, slowly stepping off the clutch & waiting before I went to WOT) otherwise I went no where just spun.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Kittens in first to claim dominance of the residence, then puppies later From past experience, the other way around can be problematic to say the least  Those weird "Dobby looking"  little kittens are not cheap....LOL
    • At least yours have parkour down pat. One of mine will still trip over his own shadow and fall over... He's a special type of cat... Ha ha ha
    • The question then becomes - was there any fluid coming from that hole before you did the rebuild ?    You may not have noticed, of course.   Depending on how you did the rebuild, the possibility has to be considered that somehow (cleaning ?)  fluid entered that hole and is now being 'forced'  out by small movements of the proportioning valve.   From the factory, there's actually a small rubber plug in that hole but with age and under-bonnet heat it's quite common for it to 'go missing'.  That rubber plug is designed to allow the venting process but also to prevent 'stuff' getting to the area (prevent corrosion, etc).   The plug is also not available as a spare part AFAIA. Personally I wouldn't race and buy a new master just yet but keep an eye on the area to see if the 'leak' continues.   If you're concerned about brake fluid damaging nearby paintwork, cable tie a piece of suitable absorbant material over the hole and remove/monitor occasionally.    Operation of the proportioning valve and the brake master itself won't be affected, but also keep an eye on brake fluid level, of course. In terms of a new master, the genuine part is getting expensive, unfortunately.  Amayama is showing AUD900+.   I was searching recently and there's an aftermarket part available from Japan made by 'Parts Assist': https://zenmarket.jp/en/yahoo.aspx?q=BNR32%2bBM50&p=1 Whether it's any good I have no idea, although in my experience Japanese aftermarket stuff is pretty good quality-wise.   The above site allows overseas buyers to purchase stuff more easily from Japan but there are fees and shipping costs, of course.   The original Japanese seller page is here: https://auctions.yahoo.co.jp/jp/auction/p1197401228 Copper/Nickel is fine but I still prefer bundy tube and it's also cheaper.
    • Your chihuahuas look weird!
×
×
  • Create New...