Jump to content
SAU Community

Recommended Posts

DRIVELINE

STILLWAY (japan) RB24DET Stroker

GTR crank

GTR rods

Custom HKS pistons

Engine block -unknown mods

Solid head conversion + unknown mods

274/274 cams

JUN Adjustable cam gears

850cc injectors

nismo fuel reg

HKS twin spark ignition system

BOSCH 040 internal pick-up

BOSCH 044 external feed

2L surge tank

GATES racing timing belt n new pulleys

standard coil packs

modded factory plenum

3" mandrel exhaust turbo to tip

custom intercooler piping and intake pipe (big G)

all internal mods are unknown as motor was built in Japan by STILLWAY company

Trust mid-mount twin scroll manifold

Trust T67-25G 10cm

Trust 48mm ext gate

OS Geiken 3-plate clutch

RB25 gearbox

custom tail shaft

standard R200 4.3 LSD -welded

standard 6bolt s13 drive shafts

Cooling

52mm alloy radiator

2x Maradyne 2350cfm each fans

B&M supercooler oil cooler

perma-cool relo kit

Standard ECU re-map by DR DRIFT

Power: 350kw@21psi on Powerplus 110 race fuel

Electronic

5 gauge AUTOMETER custom dash

-oil psi

-oil temp

-boost

-water temp

-3 5/8" rev tacho

switches for ignition, start, fans etc etc

Body

widened front guards

rear guards chopped

30mm widebody skins

topstage rear flares ontop of widebody

BA XR8 GT bonnet bulge

2UP headlight clear lenses

MARS side indicators

MARS 180sx front bar indicators

URAS N+ aero front bar

s13 aero skirts

Wheels

SSR Viennas

17x10 -19 (F) 215/40/17

17x10 -39 ® 235/45/17 (with 20mm 4->5 conv spacers)

skids: 17x10 D1Rs

Suspension

HKS HyperD fronts 10kg springs

TEIN HR rears 6kg

Adjustable caster rods

HEYMAN knuckles (troy)

GKTECH lock spacers

alloy cradle lockers

Interior

RECARO SR3 drivers

whatevers available on the day passengers seat

SABELT 3" ratchet harness drivers

SABELT 2" passengers...meh

back seats

rear seatbelts LOL

FULL TRIM smile.png

*soon to be all removed when i can F$%$Ked*

car is still in development stage as been building for last 3yrs and only seen 2 track days since

post-43210-0-88048200-1330410771.jpg

post-43210-0-97152300-1330954378_thumb.jpg

cbf writing up a whole story on the car guys so heres a picture story

where it all began as a CA18DE here shown jus with coilovers n wheels

post-43210-0-79949600-1331040262_thumb.jpg

removed bashed doors n chucked on doors from my old bent s13 n a bit of nismo/garden edge love

post-43210-0-52610100-1331040261_thumb.jpg

went reverse panda

post-43210-0-16648100-1331040260_thumb.jpg

at this stage it was CA18DE+T with a full trust TD05 kit...2 weeks later blew the headgasket so freshened up the motor chucked some JUN Cams in n was ready to go back in

post-43210-0-30791400-1331040467_thumb.jpg

then the RB24 popped up for sale from my mate, whom brought it down in a 32 drag/wangan car from japan was making 370kw on pump98 with a TO4Z with massive boost leak n coil packs cutting down

so the CA got ditched n then started the long n draining story of this silvia build

pictured here with its first turbo setup...HOLSET HX35W of a diesel truck engine

post-43210-0-84006700-1331040281_thumb.jpg

post-43210-0-73601800-1331040283_thumb.jpg

new fans n radiator

post-43210-0-93461200-1331040270_thumb.jpg

just b4 calder drift attack

post-43210-0-82694000-1331040278_thumb.jpg

ummm...dont ask

post-43210-0-60573900-1331040471_thumb.jpg

new look for matsuri n more rear offset

post-43210-0-56761000-1331040265_thumb.jpg

love my dash...

post-43210-0-80065200-1331040274_thumb.jpg

n finally....

post-43210-0-03569800-1331040288_thumb.jpg

this is the exact same engine from the s15 in the very popular youtube video lol

  • Like 1

Great first post for a build thread - if only the rest had all that detail and information, well done.

This car would be a riot to drive too, love it

thanks bro yer it is a handful n loves wide open throttle :)

wow , so is there anything left to do to the car apart from taking trim out?

pretty much only thing left...left the trim in there because initial plan was to keep it a street car but lost my licence too many times n thought otherwise

Interesting car mate, can I ask how it feels with the spring rates you have? Seems a little odd. Nice build though!

thanks bud

car feels stupidly quick, i like more of a soft setting to maintain full traction under full throttle even my front dampeners are on level 2 out of the 12 available lol

i still gotta get camber arms n toe arms for the rear n wind it out to about +.05 camber then just hold on for some stupid high speeds lol

  • 2 weeks later...
  • 3 years later...

*EDIT*

for those interested, this motor took a turn for the worse after not even 3 track days, at calder i broke the oil pump when i went to clutch 4th due to a very early gear change on my part...the force of the 3-plate clutch pushed the crank straight thru n1 oil pump ending my day

however we pulled the motor down realized it was a godsend, the bearings were very close to be needing to be replaced and the crank was unharmed so a full overhaul was decided

also to those interested that was expecting a full house list of components myself included, well a surprise was in place

internals:

STOCK crank

STOCK rods

STOCK toyota piston

head:

STOCK

cams:

still unknown duration and lift

injectors:

mazda rx7 550cc

headgasket:

tomei(assuming)

oil pump:

n1

we were so shocked at how such a basic modded motor could put out the power it has done

here's a list of upgrades that will be going in/around the motor

ARP head studs

ARP main studs

ARP conrod bolts

TOMEI 1.2mm head gasket

BOSCH injectors(most likely 1000cc)

REIMAX oil pump gears

LIMIT bigger sump with tomei baffle

LIMIT oil breathing system/can

LIMIT surge tank

044 x2

SPOOL head drain kit

TD06H-25G 10cm turbo

TURBOSMART PRO-gate

MICROTECH LT12 ECU

and since scrapping the track s13 the motor will now reside in my daily driven R32 sedan

Edited by UNDR8D MOTOWORX

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • just an update to this, poor man pays twice  Tried sanding down the pulleys but it didnt do the trick. Chucked another second hand alternator in the na car which I got for free off my mate and its fixed the squelling. Must have been unlucky with the bearings.    As for my turbo car, I managed to pick up a cwc rb alternator conversion bracket + LS alternator for 250 off marketplace, looked to be in really good nick. Installed it , started the car and its not charging the battery.... ( Im not good with auto elec stuff so im not sure if this was all I needed to do but I verified such by using a multimeter on the battery when the engine was running and I was only getting 12.2v )   I had to modify the earth strap for the new LS alternator , factory earth strap was a 10mm bolt which did not fit the bolt on the LS alternator which was double the size so I cut it off , went to repco bought some ring terminals that fit, crimped it onto the old earth strap and bolted it up to the alternator , started the car and same issue. Ran like shit and was reading 12.2 at the battery.  For a "plug and play" advertised kit thats not very plug and play but alas.  My question is , am I missing something ? Ive been reading that some people recommend upgrading the stock 80 amp alternator fuse to a 140 amp but I dont see how that would stop the alternator charging especially at idle not under load.  Regardless ive pulled it out and am going to get it bench tested by an auto elec tomorrow but it would be handy to know if ive missed something silly or have done something wrong.   
    • My wild guess is that you have popped off an intake pipe....check all of the hoses between the turbo and the throttle for splits or loose clamps.
    • Awesome, thanks for sharing!
    • To provide more specific help, more information is needed. What Android screen? What is its wiring diagram? Does the car's wiring have power at any required BAT and ACC wires, and is the loom's earth good?
    • So, now all you need to do is connect the 2 or 3x 12v feeds into the unit to permanent 12v, ACC 12V and IGN 12V that you can find in the spot behind the stereo, and the earth, and then it will switch on with the car.
×
×
  • Create New...