Jump to content
SAU Community

Recommended Posts

Hey guys, I've had a vacuum leak problem or what I think is a vacuum leak problem for quite some time. My engine sometimes hunts, mostly when I take the key out and the turbo timer kicks in. One time I drove out the carwash and my engine was hunting real bad almost cutting the engine and when I put the foot down it just went CHUG CHUG CHUG and struggled to get up to speed with ALOT of fuel spitting out the back. I've ziptied alot of the small hoses coming out of the intake manifold(A 4mm or 6mm line on the back of the manifold allowing my gauge to read something and all hoses that size out of the manifold). I've only worked on marine diesel engines so I have no clue what to look for or what i'm even looking at too be honest haha.

Here's what my gauge reads normally and I would think its meant to be right down on the -7? I'm not 100%

cKrHw.jpg

Also i've found these stains on this hose coming near the front of the manifold, the side closest to the rocker cover but I never realised fluid even went into the intake manifold but there is a tiny coolant leak around this area somewhere too I can see a few drops on the block underneath it.

lMDmt.jpg

And this screw here(Pipe leads into my radiator) is damaged and not tight but again I don't know if it's even a problem

ZoxQD.jpg

If anyone could help me i'd be extremely thankful as I have a feeling i'm losing boost pressure due to this aswell and my fuel consumption is effected.

Thanks!

-Joe

EDIT:

Edited by Jo33
Link to comment
https://www.sau.com.au/forums/topic/402576-cant-find-my-vacuum-leak-help-pics/
Share on other sites

sounds like a few problems you have there! the car wash misfire sounds like water on the ignition system, have a look at your coils and plugs and check if water is / has gotten in there

Edited by StevenCJR31

That earth wire is the main ECU earth. VERY important

Also clamp off the big tube that goes to idle air control. The engine should stall. If it doesn't, you've got a vacuum leak at the charcoal canister. Delete it to diagnose

Lookin gat your vacuum/boost guage......that is a completely normal idle vacuum. You will never see -700mmHg. Usually halfwayish between 350 and 700.

The coolant is normal. There is a coolant blled screw right there (I think it's the 10mm one on the edge of your circle. Open it to bleed, coolant drops out. Normal.

Lookin gat your vacuum/boost guage......that is a completely normal idle vacuum. You will never see -700mmHg. Usually halfwayish between 350 and 700.

The coolant is normal. There is a coolant blled screw right there (I think it's the 10mm one on the edge of your circle. Open it to bleed, coolant drops out. Normal.

Thanks for clearing that up, I've never seen boost pressure measured in mmHg always psi or bar so I didn't know what to expect.

Thanks for all the tips guys once I get home tonight i'll pick up all the gear I need on the way home and hopefully the hissing noise and hunting stops :D

It may have something to do with the turbo timer. Try leaving it idle without the timer on. Just leave key on. If it doesnt happen then its the timer

Id agree with that too. The turbo timer in mine used to make the car revs dip every time it beeped as it counted down. Never figured out why and couldnt be bothered unwirng it so just turned it off and hid it haha.

Edited by gotRICE?

Id agree with that too. The turbo timer in mine used to make the car revs dip every time it beeped as it counted down. Never figured out why and couldnt be bothered unwirng it so just turned it off and hid it haha.

It's called cheap install

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I've looked up the parts number (41011AL501). It's around $700 OEM. Usually our Infiniti G35 here in Canada have interchangeable parts with my Stagea but the parts number are not the same. I have looked around and it seems the JDM 2005 V35 Skyline (which is the same as our G35) has the same caliper but I cannot confirm. And I can't find a repair kit. The inner brake pads drags on the rotor, seems to be rusty piston. Thanks for the info by the way
    • This coupled with 6-9 speed autos with ridiculously short gearing is why these modern shitbox cars always seem so fast off the line. If it wasn't for those things, Raptors would not seem fast. The problem we have is there is a driveability gap between a more gentle take off and a wheelspinning sideways launch. The difference between ankle flex required to achieve one and ankle flex required to achieve the other is about 0.5°.
    • Yeah I think I'm also with the opposite here. It's 'hard to keep up with traffic' because in the real world I'm accelerating with 15% throttle and they are pinning it. It feels like I'm being an overt dickhead at anything above 15% throttle, so the car sounds like I'm being an overt dickhead to keep up with/get ahead of traffic when I'm really just trying to drive with traffic. There would be no issue 'keeping up with traffic' if we used the same level of throttle input/aggression to drive around. People really do just drive around with their foot nearly pinned in econoboxes.
    • To be fair it's the other way around. 300kw is boring in a modern Golf or BMW. They are so competent / well-engineered / devoid of emotion that you have to go stupid fast to feel anything. Whereas the <300kw RB still makes all the right noises and it feels good to drive. Can pull off at the lights with the turbo whooshing and the blow-off pssshing and feel like the coolest kid on the block. Just don't look to the side where you'll see the bored housewifes in their shitbox Yaris/Corolla/Camry that kept up because you didn't go fast at all
    • 300kW is so boring in a Skyline, you'll get spanked by someone's mum's Golf with Alibaba pipes, and an email tune.
×
×
  • Create New...