Jump to content
SAU Community

Recommended Posts

Hi Gurus,

Sorry if this has been covered, but I have searched the interwebs and cannot find any answers.

I did a service on my R33 Series 2 about 3000kms ago with K&N oil filter and Motul 5w40 full synthetic.

I checked the oil level on the dip stick this morning and the oil was already on the low level. There are no leaks that i can see on the engine itself or under the car and i park the car in 2 same locations everyday so it would be visible if it was leaking from under the car.

What could this mean ? or is it normal for skylines to drink oil ?

I understand that its normal for old cars to drink oil but my r33 has only 123,000kms and full service logs and has been stock its whole life.

Cheers

Link to comment
https://www.sau.com.au/forums/topic/402890-drinking-oil/
Share on other sites

On an oil change I always fill so that it ends up sitting on the high (hot) mark AFTER the car has fully recirculated the oil.

This means you can then very easily see if the oil were to drop for any reason during service intervals. Mine never does but if the day comes when i do ill know straight away.

Rb's also seem to be a bit safer with a higher oil level, especially if you give them some revs n cornering...

Link to comment
https://www.sau.com.au/forums/topic/402890-drinking-oil/#findComment-6406612
Share on other sites

i would put 5 litres into it, not 4.3

bingo.

and just a random bit of trivia to make all us RB owners feel better about the amount of oil we need to feed our beasts. Particularly modified RB26's

- The Lamborghini Aventador needs 13 litres of what im sure is some pretty top of the line fully syn

Link to comment
https://www.sau.com.au/forums/topic/402890-drinking-oil/#findComment-6406717
Share on other sites

I just rechecked it this morning and the level seems to be at the same level as when i filled it up(hasn't dropped). I also checked the radiator for oil and it seams to be clear.

I must have checked on a very slight angle, i have read somewhere that on a skyline even the slightest angle makes a huge difference to the reading.

Thx for all the replies.

Link to comment
https://www.sau.com.au/forums/topic/402890-drinking-oil/#findComment-6407898
Share on other sites

sitting on the high (hot) mark

It's H for HIGH, not H for HOT.

If you replace the oil filter at the same time as you do an oil change, you need to put most of the oil in and run the engine for a few seconds before checking the oil level in the sump. Then add oil to bring the level up to the H mark.

Link to comment
https://www.sau.com.au/forums/topic/402890-drinking-oil/#findComment-6408183
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I can see between the water jacket and cyl 3 there wasn't a hard line of combustion gas. It certainly appears that the issue is coming from there. Yes, checked the tension. All at 100ft lbs where I set them 5 years ago. These blocks can crack but generally when they have been over bored. Mine is only 0.5mm oversize at 89.5mm. They break between cylinders around the 91mm mark. No sign of that with mine. My gut feeling is the head gasket lifted a while back when the studs stretched and i bandaided it by retorquing the studs. It's finally let go.
    • My Nismo 1.5 churps a bit on reverse turns when cold, but besides that feels like a stock diff.
    • Yes, but, I paid cash and I'm pretty sure the receipt was in the bin 10 minutes after I got home Note to self, keep all receipts
    • Bunnings would have just handed you your money back on that one!
    • So, version 4 intake is on its way I was looking at these a while ago but at around $200 or more it was a little pricey for something that might not work, but, I had it in my watch list, but, I got a message saying it was on special, and I had a code thingie to use, it eventually came in at $120 delivered, so BAM, BUY NOW.....LOL I'll need to have a look when it arrives but I feel it will "look" better than what I currently have, as it comes with a PCV fitting, so I will be able to get rid of the alloy pipe that goes to the throttle body with the PCV fitting  Well, that's what the voices in my head are telling me  Oh, and this happened today Yeap, it was a Trojan, and it was cheap, so I headed back to the hardware store and actually spent a little bit more on a heavy duty,  one that was actually recommended by a plumber mate, a Cyclone one with a fibreglass handle that is actually rated for clay The broken shovel will eventually be "modified" into a short handle shovel
×
×
  • Create New...