Jump to content
SAU Community

Cd Err Fo Fix

Stayer
 Share

Recommended Posts

Stayer Enthusiast

Stayer

Posted
Posted (edited)

Has anyone find out who can get our Bose-Clarion PN-2414e unit with this error fixed in Australia or overseas and for how much? Or better yet, has anyone fixed it themselves?

There are a few reasons for this error to appear -

Circuit board problem

Cracked plastic gear

Jammed mechanism

The reasons for my CD ERR FO is the mechanism jamming which occured when I was switching tracks. I took the CD-Changer apart with the help of my father-electrician, but it proved too complex for him to figure out which part is stuck. The mechanism looks intact and not tampered with before - the car had just 40k on clock when bought.

The solutions I am considering -

Buying new unit from the US ($300), but it is missing one of the output at the back - probably for Navigation which I have.

Sending old unit to the US for repair ($150 repaired plus shipping)

Edited by Stayer
Link to comment
https://www.sau.com.au/forums/topic/403882-cd-err-fo-fix/
Share on other sites
sonicii Veteran

sonicii

Posted
Posted

You can get them fixed in Aust, but I believe the cost is significant. It would be worthwhile looking at the double DIN facia and an aftermarket head unit.

If you want to keep a factory type unit, you could post it to the US for repair. Or you should be able to pick up a 2nd hand G35 head unit for less than $300. I picked up a bose G35 head unit for US$170. If you decide to go down this route, you have the obvious risk of it not working when it gets here.. If you go new or 2nd hand from USA, make sure you buy like for like (bose with navi with a G35 bose with navi), then it should be a simple swap. And the G35 HUs can play MP3 CDs.

The hard part will be getting your CDs out of the old unit.. I believe it requires major surgery..

Link to comment
https://www.sau.com.au/forums/topic/403882-cd-err-fo-fix/#findComment-6426268
Share on other sites
Stayer Enthusiast

Stayer

Posted
  • Author
Posted

You can get them fixed in Aust, but I believe the cost is significant. It would be worthwhile looking at the double DIN facia and an aftermarket head unit.

If you want to keep a factory type unit, you could post it to the US for repair. Or you should be able to pick up a 2nd hand G35 head unit for less than $300. I picked up a bose G35 head unit for US$170. If you decide to go down this route, you have the obvious risk of it not working when it gets here.. If you go new or 2nd hand from USA, make sure you buy like for like (bose with navi with a G35 bose with navi), then it should be a simple swap. And the G35 HUs can play MP3 CDs.

The hard part will be getting your CDs out of the old unit.. I believe it requires major surgery..

thanks for that! where did you get it from if you don't mind me asking?

also, isn't the G35 unit you bought comes from Series 2 G35? I believe Series 2 (2005) V35s had MP3 player already.

I would be happy to get Series 2 Head-Unit with MP3 function, however, not sure if it would fit Series 1 as Series 1 has climate controls inside it and Series 2 doesn't.

Link to comment
https://www.sau.com.au/forums/topic/403882-cd-err-fo-fix/#findComment-6426415
Share on other sites
sonicii Veteran

sonicii

Posted
Posted

That's a good point, you will need to get a S1 deck if you have a S1 V35. I believe the connectors are different between the S1 and S2. Also, as you know, the face panel is different, and you will probably need this from the G35 too.

The S2 V35 doesn't play MP3s.. it does had a MD player, perhaps that is where the confusion has come from? That is the main reason I got the G35 HU, as I wanted MP3 playback. and it was cheaper than the Double DIN setup or the iPod I/F.

I found mine on the G35driver 'for sale' section. They pop up on there every now and then.

Link to comment
https://www.sau.com.au/forums/topic/403882-cd-err-fo-fix/#findComment-6426502
Share on other sites
NISMO-61 Contributor

NISMO-61

Posted
Posted

I had the same issue when I got my car ages ago. I simply removed the unit and give it a nice kick, then all the CDs came out, but mine had other issues (no sound at all) you might wanna give it a go. Remove the unit and shake it a little bit. or better replace it with a 7" DVD player as I did.

Link to comment
https://www.sau.com.au/forums/topic/403882-cd-err-fo-fix/#findComment-6437465
Share on other sites
  • 3 weeks later...
  • 3 weeks later...
Stayer Enthusiast

Stayer

Posted
  • Author
Posted

sent 3 of you the link too

to be clear, that's the link to the offer of repair service

however, after I told him that I'm from Australia, he offered me to sent CD-Mechanism for the cost of repair to save me on shipping costs

also, CD ERR F0 may results from different problems (electrical, for example), mine was purely mechanical as CD-Mechanism stuck while I was changing disks on the move

so, talk to the guy about your problem

Link to comment
https://www.sau.com.au/forums/topic/403882-cd-err-fo-fix/#findComment-6492626
Share on other sites
  • 5 months later...
Nightcrawler Grand Master

Nightcrawler

Posted
Posted

I do like how you said "the car had just 40k on clock when bought." .... I haven't seen a V35 go through the Jp auctions with 40k on it since about 2005, yet you can find them all along Parramatta Road and other similar places with these sort of km on them. Truth be told for under $100 a guy can come out and make your odo say whatever you want. Just sayin'.

Link to comment
https://www.sau.com.au/forums/topic/403882-cd-err-fo-fix/#findComment-6727225
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • funkymonkey
      Jacks that fit under GTR lips that can reach the subframe?

      By funkymonkey · Posted

      I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • Duncan
      Mistakes were made, my R34 Story

      By Duncan · Posted

      You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
×
×
  • Create New...