Jump to content
SAU Community

Recommended Posts

The Bosch 044 I just found out was a 700hp pump which is hell good enough I'm

Not sure what pump I have I bet it's a standard gtst pump running a rb26 I got the car like that I can hear the pump dying in the ass when u let it prime up with the ignition on u can get Bosch 044 rip offs for 70 buck eBay bloke reckons he runs them in his race car but there 100 less lph then the real thing not sure if I trust copy's of the Bosch 044

  • Replies 66
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Lol at copies, as if you even consider that espicially for something crucial like a fuel pump which youve just leRnt the hard way.

If you can afford 500 go nismo its direct fit 10 min install but if you want to save abit go the 044 for 200 bux just have to muck around a little to make it fit in stock position.

Yeah but the thing is I don't know if it was my fuel pump or why waste money if I don't know all I no is that it was melting the outsides of the pistons it's was running then just stalled like out of fuel lost compression and little bits of steel shavings where in the bores from the tops of the outsides of melted pistons

I have new motor

So as Jez said; put it in, drive it sedately to a tuner, and get them to check everything out.

You could also just pull your fuel pump out and check what it is, takes 10 minutes. If it's a stock GTST pump then you can be fairly certain that's what the issue was.

Im going a genuine 044 Bosch yeah I'm not sure close to 500 I think but I bOught the car like that next thing it's starts detonating when being thrashed cracks a ring land ok then new piston and rings where put in then it stalls and loses compression

I have a standard rb26 boosted up to 14psi with a full exhaust and pods that's all mate

Im going a genuine 044 Bosch yeah I'm not sure close to 500 I think but I bOught the car like that next thing it's starts detonating when being thrashed cracks a ring land ok then new piston and rings where put in then it stalls and loses compression

500hp with a standard 26 with a bit of boost? You have no idea what you're talking about do you lol?

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Started sifting thru my brakes to decide which ones I will run on Clem   Made me think I should just put them all on Silver...for when brake fade just isn't an option   Should be able to bump rotor up from 343x32 to 348x36 off Supra. Not sure if the Supra annulus is right for the Alcons or APs but trying g to find a used Supra\M4 rotor to test fit The Alcons seem to gain 1-2mm clearance which all helps  
    • So car is getting a few mods to the cage and some jacking points welded in Meantime Ol Silver gets a new gearbox and shiny clutch.  Old Box is being set aside for Clem  
    • Probably speedometer itself if the odometer is ticking. If the needle is stuck from a bit of grease or something that can cause it to stay at 0. Or a cracked solder joint in the speedometer can do it too.
    • Thanks Fella’s   to take this off topic and to elaborate a bit more. I have an rb25/30 going into a r32 GTST.. expected to make around 600-700hp. Would you?   A) R34 GTT box   B) CD00#?  I’ve seen a few posts about the CD swap and sounds fairly involved with making it fit etc but if it’s worth the work then I’ll go that way
    • Lower at the hubs. Funny I forgot to mention that part. Do this pull here I turned the camera off too soon but the graph shows a drop at the top and that was because the pipe from the turbo blew off. The tuner said we could’ve made possibly another 15 whp. He also added if I switched to ethanol we could up the boost some more as well. I was comfortable capping it at the most of 20 pounds. Turns out the turbo pipe just needed a new worm clamp. Got home replaced that then did a third gear pull from 3k to 7200 rpm and the power was great to the top. I just got an ecu mounting bracket from IEE that I need to try and get everything to fit well. It’s a PITA to get the harness and ecu fit properly behind that kick plate 
×
×
  • Create New...