Jump to content
SAU Community

Recommended Posts

The Bosch 044 I just found out was a 700hp pump which is hell good enough I'm

Not sure what pump I have I bet it's a standard gtst pump running a rb26 I got the car like that I can hear the pump dying in the ass when u let it prime up with the ignition on u can get Bosch 044 rip offs for 70 buck eBay bloke reckons he runs them in his race car but there 100 less lph then the real thing not sure if I trust copy's of the Bosch 044

  • Replies 66
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Lol at copies, as if you even consider that espicially for something crucial like a fuel pump which youve just leRnt the hard way.

If you can afford 500 go nismo its direct fit 10 min install but if you want to save abit go the 044 for 200 bux just have to muck around a little to make it fit in stock position.

Yeah but the thing is I don't know if it was my fuel pump or why waste money if I don't know all I no is that it was melting the outsides of the pistons it's was running then just stalled like out of fuel lost compression and little bits of steel shavings where in the bores from the tops of the outsides of melted pistons

I have new motor

So as Jez said; put it in, drive it sedately to a tuner, and get them to check everything out.

You could also just pull your fuel pump out and check what it is, takes 10 minutes. If it's a stock GTST pump then you can be fairly certain that's what the issue was.

Im going a genuine 044 Bosch yeah I'm not sure close to 500 I think but I bOught the car like that next thing it's starts detonating when being thrashed cracks a ring land ok then new piston and rings where put in then it stalls and loses compression

I have a standard rb26 boosted up to 14psi with a full exhaust and pods that's all mate

Im going a genuine 044 Bosch yeah I'm not sure close to 500 I think but I bOught the car like that next thing it's starts detonating when being thrashed cracks a ring land ok then new piston and rings where put in then it stalls and loses compression

500hp with a standard 26 with a bit of boost? You have no idea what you're talking about do you lol?

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • So for the wide band is a Bosch 4.9 correct for the Link G4+ along with a Can bus? Just get the Link gear or is generic ok too? Eg here: LINK LINK DIGITAL WIDEBAND CAN MODULE WITH BOSCH 4.9 SENSOR : KYP Performance House  
    • Bit difficult to follow. Have a look below and see what the standard R32 layout was like. Note there was a restrictor in place immediately before "turbocharged pressure control solenoid" that, if removed, magically got you 1 bar boost.
    • I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
×
×
  • Create New...