Jump to content
SAU Community

Recommended Posts

High everyone,just taken delivery of my R34gtr v-spec,thanks to everyone at Iron chef imports,just to the right of the steering column is a switch,click to the right and there's a noise from the rear end,hold to the left and the engine starts labouring.And there's a box under the front seat,anyone got any idea what these might be. :wub:

post-93096-0-00040000-1337858857_thumb.jpg

post-93096-0-08098800-1342222543_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/404679-what-are-these/
Share on other sites

I found another part of the quiz,under the parcel shelf in the boot,

post-93096-0-52785900-1342351836_thumb.jpgpost-93096-0-24627900-1342351848_thumb.jpg

this is another view of the box under the driver's seat

post-93096-0-97203100-1342351817_thumb.jpg

for some reason the photo of the button on the dash in the first post has vanished so here it is again

post-93096-0-47451100-1342351857_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/404679-what-are-these/#findComment-6444840
Share on other sites

Mate just did a quick google search on 5zigen and there a Japanese company that specialize in rims and exhaust systems. I couldn't find much info on that box but my guess is it would have something to do with the exhaust system. There is probably some kind of butterfly in the exhaust that adjusts when you press the button. Check if it's the same brand exhaust. What happens when you drive with it switched to the right, is it louder? Is it quiter when the button is flicked o the left?

Or you could try emailing the company to find out. Apparently there the third largest exhaust company in Japan

Link to comment
https://www.sau.com.au/forums/topic/404679-what-are-these/#findComment-6445268
Share on other sites

It's got the nismo exhaust with the oval tip.I flicked the switch to the right yesterday,no difference in sound,but when i put it in reverse a buzzer sounded so i flicked it back to the center.Then when driving up the road i flicked it to the right and it was like it went into neutral so l flicked it back to the center.Does all R34gtr's have this little black box on the end of the gear box.post-93096-0-07642200-1342401038_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/404679-what-are-these/#findComment-6445306
Share on other sites

It's got the nismo exhaust with the oval tip.I flicked the switch to the right yesterday,no difference in sound,but when i put it in reverse a buzzer sounded so i flicked it back to the center.Then when driving up the road i flicked it to the right and it was like it went into neutral so l flicked it back to the center.Does all R34gtr's have this little black box on the end of the gear box.post-93096-0-07642200-1342401038_thumb.jpg

black box is normal there - no idea what its for, but its on mine too.

i've got something similar under my seat too - been meaning to check out what it is - i'm away for work atm, but i'll check when i'm back on wednesday.

Link to comment
https://www.sau.com.au/forums/topic/404679-what-are-these/#findComment-6445556
Share on other sites

The black thing at the back of the gbox is actually a vibration/shock damper, made of rubber with steel weight.

The device looks like some sort of hydraulic controller, with the unit having metal lines coming off a master cylinder of some sort. Never seen someting like that before.

You need to follow the lines under the car to see where they go...

Link to comment
https://www.sau.com.au/forums/topic/404679-what-are-these/#findComment-6446046
Share on other sites

Ok i got a reply back from 5zigen and it's a twin plate clutch kit.When it's activated you can change gears with out useing the clutch.They say there's a button on the shift knob,which there isn't.So i sent them a photo of the one on the dash.Stay tuned.

Edited by I gotta R34gtr v-spec
Link to comment
https://www.sau.com.au/forums/topic/404679-what-are-these/#findComment-6447724
Share on other sites

So sounds like it is rigged up to operate the clutch slave cylinder without you pushing on the pedal.

So something like this: The second clutch master cylinder in the boot shelf is operated with the dash switch to the control box, this then operates a motor and the gearbox with linkage to the end of the clutch master piston.

The hydraulic lines then go from the boot master cylinder to another reservior (maybe) as well as tee into the slave cylinder on the side of the gbox to operate the clutch.

Would be handy for a person lacking proper leg movement or leg(s) to operate a clutch pedal, so he or she wouldn't be stuck with driving an auto, or 'clutchless' shifting type of driving, ie push a button instead of pushing a pedal.

That would explain the lack of drive when you push the switch while driving in gear. Would be the same as pushing in the clutch pedal.

Pretty mad setup!!!!.

Link to comment
https://www.sau.com.au/forums/topic/404679-what-are-these/#findComment-6447835
Share on other sites

Another email from 5zigen,they say this buttonpost-93096-0-47451100-1342351857_thumb.jpg doesn't have anything to do with the system and is standard in a GTR ,it's the gauge dimmer,Is this correct.It's definetly not the gauge dimmer in my car.

Link to comment
https://www.sau.com.au/forums/topic/404679-what-are-these/#findComment-6448997
Share on other sites

The switch on the right is the headlight beam height adjustment.

The one on the left is not stock, and you mentioned it operated the clutch disengagement.

Dimmer knob is fitted for compliance as they don't come standard with a dash light dimmer. But they usually fit it where that switch is...

Link to comment
https://www.sau.com.au/forums/topic/404679-what-are-these/#findComment-6450417
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Even with the piston at TDC there was room for it to drop, but I don't think it can drop fully into the cylinder, the problem you have is that you need something pushing against the valve to hold it up so you have enough room to put the new stem seal on and the spring etc.  I used compressed air only because putting rope in the cylinder seemed a bit risky to me, I know people have done it countless times before like this. Overall it's a pain in the ass job. Honestly you'd probably be better off taking the head off because the risk of dropping something in the engine and the finicky-ness of it all is very stressful. If you are going to attempt it though i 10000% recommend a 36050 valve spring/keeper tool. I had both the traditional lever type and after doing 1 cylinder it was absolute pain to get those valve keepers in place, even with 2 people. That 36050 is amazing, you do have to push hard to get them in place but it works perfectly almost every time. Back to my actual issue I think my engine is just tired and old and the rings have gone bad. The comp numbers (cold, no oil) were: Cyl 1 -129psi Cyl 2 - 133psi Cyl 3 - 138psi Cyl 4 - 137psi Cyl 5 - 157psi Cyl 6 - 142psi   Cylinder 5 and 6 having the most carbon on them.
    • Who did you have do the installation? I actually know someone who is VERY familiar with the AVS gear. The main point of contact though would be your installer.   Where are you based in NZ?
    • Look, realistically, those are some fairly chunky connectors and wires so it is a reasonably fair bet that that loom was involved in the redirection of the fuel pump and/or ECU/ignition power for the immobiliser. It's also fair to be that the new immobiliser is essentially the same thing as the old one, and so it probably needs the same stuff done to make it do what it has to do. Given that you are talking about a car that no-one else here is familiar with (I mean your exact car) and an alarm that I've never heard of before and so probably not many others are familiar with, and that some wire monkey has been messing with it out of our sight, it seems reasonable that the wire monkey should be fixing this.
    • Wheel alignment immediately. Not "when I get around to it". And further to what Duncan said - you cannot just put camber arms on and shorten them. You will introduce bump steer far in excess of what the car had with stock arms. You need adjustable tension arms and they need to be shortened also. The simplest approach is to shorten them the same % as the stock ones. This will not be correct or optimal, but it will be better than any other guess. The correct way to set the lengths of both arms is to use a properly built/set up bump steer gauge and trial and error the adjustments until you hit the camber you need and want and have minimum bump steer in the range of motion that the wheel is expected to travel. And what Duncan said about toe is also very true. And you cannot change the camber arm without also affecting toe. So when you have adjustable arms on the back of a Skyline, the car either needs to go to a talented wheel aligner (not your local tyre shop dropout), or you need to be able to do this stuff yourself at home. Guess which approach I have taken? I have built my own gear for camber, toe and bump steer measurement and I do all this on the flattest bit of concrete I have, with some shims under the tyres on one side to level the car.
    • Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
×
×
  • Create New...