Jump to content
SAU Community

Recommended Posts

Hi Guys,

I've got the following parts for sale. PM or call me. 0421 973 558. Pick up referred.

HKS Type S front mount turn flow intercooler kit.

As arrived from Japan. Condition is not 100%, some fin damage and end tank repaired, but looks to be ok. Comes with all piping, brackets, bolts, hose clamps, HKS silicone joiners, fitting instructions, etc.

Doesn't have the pressure drop and flow restrictions of the kits with the return pipe under the intercooler. Haven't fitted it to the wife's 34 sedan, as we are selling it.

$250

IMG_1629.jpg

IMG_1630.jpg

IMG_1632.jpg

Unknown Jap stainless long split front pipe.

As arrived from Japan. Good condition, minor scrape on bottom. Has had an o2 bung welded into it. Has bracket to mount to gearbox. 3" flanges, splits into 2 2.5" pipes and merges back into 3" pipe. Beautifully made. Great for getting low and staying legal.

$150

IMG_1634.jpg

IMG_1635.jpg

Stainless split dump pipe. Good condition. SOLD

High flow 2.5" cat. Great condition, no blockages. Upgraded to 3" cat. $50

IMG_1609.jpg

IMG_1610.jpg

Stainless Steel door plates to suit R34 4 door.

Fantastic condition. Will be a shame not to fit them to the car. Selling for a lot less than I paid to get them here from Japan. Black mark on front door plate rubs off. $250

Skyline007.jpg

Skyline008.jpg

R34 Instrument panel dress up panel.

Carbon fibre overlay with chrome gauge rings.Excellent condition. Very nicely made. As arrived from Japan. $200

Skyline003.jpg

URAS R34 4 door roof spoiler.

Brand new, as arrived from Japan. Not painted, but in black gelcoat. Perfect fit. SOLD

Factory R34 4 door rear lip

Genuine series 2 rear boot lip. Has clear LED brake light. The rear lip was damaged in transit from Japan but is repairable. SOLD

R34 Series 2 front bar

Fantastic condition. Complete with grill, badge and clear indicators. As arrived from Japan. I only unwrapped it tonight to take pics! $250

Skyline012.jpg

Skyline013.jpg

Skyline014-1.jpg

4 door weather sheilds

Excellent condition. Didn't even make it onto the car. Hard to find in good condition. $200.

Skyline010.jpg

Skyline009.jpg

R34 4 door window switches

Good condition. Series 2 so it has a Joystick for mirrors. $80

Skyline011.jpg

R32 GTR front lip

Reasonable condition. small crack in plastic near mounting tab. Will need paint. SOLD

More parts and pics listed below as the forum wont let me upload so many pics in 1 post.

Cheers

Scott

Edited by SABBAi

Hey mate... How much for the bar and does it come with the reo? Also you dont have a dump pipe at all do you? Like what comes with the 4 door exhaust, is it just cat back? And how much for scuff plates? Could I get pics of bar and plates to [email protected]?

Hi Chris,

I'll get some pics and prices up tomorrow for you. The front bar doesn't have the reo, it's just the skin, it does have the indicators and grill however. The 4 door exhaust is a cat back. I do have a split dump also.

pics tomorrow.

Yah cool, im gonna get the justjap full dump pipe but just though i'd check... you dont have the cold air intake part of the air box do you? the part going from rad support to air box?

Hey Chris, the front pipe is 304 stainless. The flanges and bracket is 314. I don't have the snorkel for the air box sorry.

R34 4 door Apexi exhaust

So I thought I bought a Fujitsubo exhaust. I hadn't unwrapped it sinse it got here from Japan. It is in excellent condition. Not a blemish. Pity it's not going on the car. I looked at what I paid for it and blushed a little. My loss, your gain. $500

Picture585.jpg

Picture586.jpg

Picture587.jpg

URAS / Monkey Magic Series 2 front lip

Brand new. Still sealed in it's bag. Great looking lip. Not sure if it'll fit an S1, but if you're local you're welcome to try.

SOLD

More parts to be added as I find them in the garage.

Hey mate, what size is the $50 split dump pipe? Would is suit a 3" exhaust? Also I have the exact same exhaust that you are selling, for anyone interested it is a top quality exhaust, it's not overly loud and definitely not droning which i like.

Hey Chris, the dump pipe will fit a 3" exhaust. I was going to run it with the split front pipe, high flow cat the Apexi exhaust.

As for R34 bars, I have the Series 2 front bar which is second hand.

Hey dude,

in ragards to the factory boot lip... do you happen to know if it covers up the factory brake light?

-Aerron

Hey Mate, yes it does. To fit the lip, you remove the factory brake light. The brake light in the lip has a loom that plugs into the brake light plug and seals the hole.

Same as the pic of the white car above. I do have the same bar as you have, but I was going to swap it for the S2 bar. Want me to bring it tomorrow night so you can see how it fits? Also, you interested in the BBS rims?

PM's have been replied to.



  • Similar Content

  • Latest Posts

    • I'm looking for some real world experiences/feed back from anyone who has personally ran a EFR7670 with a 1.05 exhaust housing or a .83 I'm leaning towards the .83 because its a street car used mostly for spirited driving in the canyons roads. I"m not looking for big numbers on paper. I want a responsive powerband that will be very linear to 8000 rpm. I dont mind if power remains somewhat flat but dont want power to drop off on top. The turbo I've purchased is a 1.05, although the mounting flange T3 vs T4 and internal vs external waste gates are different on both housings, I not concern about swapping parts or making fabrication mods to get what I want. Based on some of the research I've done with chat gpt, the 1.05 housing seems to be the way to go with slightly more lag and future proofing for more mods but recommends .83 for best response/street car setup. AI doesn't have the same emotions as real people driving a GTR so I think you guys will be able to give me better feed back 😀   
    • Surely somebody has one in VIC. Have you asked at any shops?  Is this the yearly inspection or did you get a canary?
    • This is where I share pain with you, @Duncan. The move to change so many cooling system pieces to plastic is a killer! Plastic end tanks and a few plastic hose flanges on my car's fail after so little time.  Curious about the need for a bigger rad, is that just for long sessions in the summer or because the car generally needs more cooling?
    • So, that is it! It is a pretty expensive process with the ATF costing 50-100 per 5 litres, and a mechanic will probably charge plenty because they don't want to do it. Still, considering how dirty my fluid was at 120,000klm I think it would be worth doing more like every 80,000 to keep the trans happy, they are very expensive to replace. The job is not that hard if you have the specialist tools so you can save a bit of money and do it yourself!
    • OK, onto filling. So I don't really have any pics, but will describe the process as best I can. The USDM workshop manual also covers it from TM-285 onwards. First, make sure the drain plug (17mm) is snug. Not too tight yet because it is coming off again. Note it does have a copper washer that you could replace or anneal (heat up with a blow torch) to seal nicely. Remove the fill plug, which has an inhex (I think it was 6mm but didn't check). Then, screw in the fill fitting, making sure it has a suitable o-ring (mine came without but I think it is meant to be supplied). It is important that you only screw it in hand tight. I didn't get a good pic of it, but the fill plug leads to a tube about 70mm long inside the transmission. This sets the factory level for fluid in the trans (above the join line for the pan!) and will take about 3l to fill. You then need to connect your fluid pump to the fitting via a hose, and pump in whatever amount of fluid you removed (maybe 3 litres, in my case 7 litres). If you put in more than 3l, it will spill out when you remove the fitting, so do quickly and with a drain pan underneath. Once you have pumped in the required amount of clean ATF, you start the engine and run it for 3 minutes to let the fluid circulate. Don't run it longer and if possible check the fluid temp is under 40oC (Ecutek shows Auto Trans Fluid temp now, or you could use an infrared temp gun on the bottom of the pan). The manual stresses the bit about fluid temperature because it expands when hot an might result in an underfil. So from here, the factory manual says to do the "spill and fill" again, and I did. That is, put an oil pan under the drain plug and undo it with a 17mm spanner, then watch your expensive fluid fall back out again, you should get about 3 litres.  Then, put the drain plug back in, pump 3 litres back in through the fill plug with the fitting and pump, disconnect the fill fitting and replace the fill plug, start the car and run for another 3 minutes (making sure the temp is still under 40oC). The manual then asks for a 3rd "spill and fill" just like above. I also did that and so had put 13l in by now.  This time they want you to keep the engine running and run the transmission through R and D (I hope the wheels are still off the ground!) for a while, and allow the trans temp to get to 40oC, then engine off. Finally, back under the car and undo the fill plug to let the overfill drain out; it will stop running when fluid is at the top of the levelling tube. According to the factory, that is job done! Post that, I reconnected the fill fitting and pumped in an extra 0.5l. AMS says 1.5l overfill is safe, but I started with less to see how it goes, I will add another 1.0 litres later if I'm still not happy with the hot shifts.
×
×
  • Create New...