Jump to content
SAU Community

Recommended Posts

Ok dudes i know i have some sort of issue with the car missing at around 4-5000rpm, which after much messin around we figure its gong to be coil packs.

We ran my car up on the dyno at my mates wshop on the weekend and ony made 134rwhp this was just over 4000 rpm

the car is r33 4door

rb25det

iridiums at 0.8

knn filter

full 3" although cat isn't hi-flowed

bleed valve standard boost ( we changed the boost in increments from 7-10psi and onlly made 2-7 hp difference

this was extremely concerning as it only put out about as much as my 900kg datto which is still pathetic.

any one else seen these types of figures.

I know there is nothing wrong with the dyno as it is the one from the recent summernats hp heroes the one that ran 1470rwhp on it, apparently most accurate in oz. i will have to tune next week but i wouldnt think that coil packs would make that much difference would they we should expect arount 200-210rwhp

comments thoughts

Link to comment
https://www.sau.com.au/forums/topic/40620-concerned-about-dyno-hp/
Share on other sites

yeh i know would coil packs rob me of that much power, the air fuel ratio was cool, the curve looked ok then bang straight back down at around 4000-5000, which is where my misfiring is, hmmmmmm, i have found that it only seems to happen under heavy load, ieif i run the accelerator easing it on lightly all the way to redline, it seems to pull the right way, but if just plant my foot nothin after the 4ish you just get the missing,

sounds like car has similar mods as mine not to sure if yours is full 3" is turbs back, butwe did notice that the standard cooler is crap as we were spraying water on it and was just drying so quickly, fmic would be handy, even yours to mine 134 to 170 is a big diff!!

we could have taken it higher but it wasnt making any power past 4000rpm

That power at those particular revs sounds about right. But you should continue to make power til about 6400, or even more with your mods eg exhaust. Peak power arrives t 6400 on a standard car. hopefully its just the coil packs.

I would think if a coil pack works ok at light load, it should also work ok at full load. Not 100% on this, but you could prolly use an Insulation Resistance tester (megga) on the 1000v scale to test it (know any sparkies?). The primary winding should have continuity from one end to the other and should not be shorted to earth. I think the secondary should also have continuity from the plug top to earth on the coil pack. Please correct me if i'm way off the mark!

rb25 you would think that yours and mine should be making more power, they are around 180-190 standard from factory?

there is wear and tear but we had an older supra on there similar mods 4 years older no rebuild more kms and put out 200rwhp and they come out with 187kw factory same as skyzers i think?

similiar problem to my tuning at CRD. Mine's FMIC, unichip, full exhaust, EBC

made 163rwkw with a stuffed coil pack, replaced it and made 181rwkw on 7psi.

Jim @CRD suggested gapping the plugs from 0.8 to 0.75 if wanted to go on higher boost as the spark was breaking down with more than 7psi. Gapped it and had a test run on .8(11psi) and .9(13psi)bar, sweet.....

I had this problem on my car....the engine was misfiring and spark was breaking down at high RPM (4000 or above). Had the workshop check it out and found that 2 of my coil packs were on the way out. I bought 2 second hand replacements from the for sale section on SAU replaced the old ones and now everything is sweet. In the meantime while running with the faulty coils the workshop regapped the corresponding spark plugs closer in order to try and reduce the misfiring. As more load is put on the coils, the spark breaks down more and arcs out causing the misfire. Check your plugs as well because there could be a lot of deposit on them which may be fouling them as well.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Oh ok that makes so much sense. Thanks for clearing it up!
    • And these modern "environmentally friendly" EV vehicles also run on the same smoke! When the engine, wiring, or batteries let it escape it also stops running!
    • Yeah - I found the same information too.. 30% open is like 85% of flow etc. So it's probably going to be minor if not completely imperceptible. I also have a larger pod filter here, will swap that on and see if there's any difference. The hardest part is finding a place to uh, test this. It's quite noticable just how much having ducting to the otherwise completely open pod cools the intake temps down. It's better boxed, or shielded but driving for 30 seconds really makes it plummet to near ambient temperatures. I recall in the past when I was a RB land and had a nice flowing airbox -  - Then I took the lid off and put a pod there, and gained 9 psi of boost and about 60kw from the restriction I didn't know I had - with the controller at same duty cycle. However finding people using over the radiator intakes having similar KPA drops at WOT on built setups makes me think there restriction could be the exhaust or potentially the headers. Either way though, there's no real estate to play with and nothing that can realistically be done about it. The original dyno plot without the airbox, and the larger pod had a better curve. It was later I added the ducting and airbox, and a smaller pod to make it fit in there...
    • That's not completely truthful now is it? Any flex fuelled factory cars also had the option to run on steam.
    • Yeah so I guess your mechanic would know turnaround better than me....but I would have thought you had access to same day or overnight rack rebuilds there....any big city here in Australia has that service.   There are a couple of o-rings and seals involved, I guess the risk is the part is specific not general. Other option is if you can have it on stands in your garage for a while, steering rack removal is pretty simple (2 mounting brackets, 2 ball joints (separate by undoing the nut to the top of the threads, put a pry bar between the steering arm and control arm to put pressure on it then medium force on the side of the ball joint or top of the nut with a hammer to break it free) and then the trickiest bit is the splines to the steering rack (not too bad to undo, one nut then it slides out, but mark it first so you can reassemble it straight)
×
×
  • Create New...