Jump to content
SAU Community

Recommended Posts

have installed some 1000cc Xspurts and im confused about the settings,

ive put in 37% correction, and the latency of the injectors is 0.990 at 14Volts and 43.5psi

so does this mean its 0.7-0.990= -.299???

when i put that in the car wouldnt even fire, when i put in 0.18 or 0.30ms it fires and wont idle but very rough, when i tried 1.0ms it was quick to fire and did idle with some throttle but still jumpy and rough...

need some help here. wondering wether theres a massive vacumn leak or if the settings are totally wrong..

Link to comment
https://www.sau.com.au/forums/topic/406328-injector-settings/
Share on other sites

The 37% correction is for the size of the injectors relative to standard. You do not use that correction when talking about the latency, and you do not refer to the original latency either. You just put in the latency number that they gave you, which is 990 micro seconds, or 0.99 milliseconds. Job done.

the tuner has emailed me that its the new latency - 0.7,

originally with the nismo 555's it was 0.18

so your certain its just put the 0.99 in then? cause its either not right or theres a massive vacumn leak..

So where the hell did the 0.99 number you've been going on about come from?

No. If the latency you have been told is 0.7, then put in 0.7. Do not pay ANY attention to what the old latency was, as it simply doesn't matter. There's no ratio, there's no correction factor. There is just numerical value.

the 0.990 comes from the deadtime chart from Injectors Online where i bought them ....thats for 43.5psi and 14volts

As far as i know from reading the forums, the standard latency is 0.7?? and your supposed to use this to calculate the adjusted latency based on the calculation new latency (0.990) minus 0.7 witch would be 0.2990...

I tried this value and it was rough as guts, and i tried 0.990 and it was even worse,

using the 0.990 from the injector chart as you have suggested drenched the plugs... im still thinking wether a vacumn leak is the course or this latency value...

Edited by SliverS2

This is PoweFC yeah?

In which case, I reverse my position on having to do maths. The standard RB25DET injectors have latency of about 0.52 ms. Your new ones are 0.99, yes? So your correction is 0.99 - 0.52 = 0.47 ms. Try that.

I didn't realise you were playing with a PowerFC until I read your sig. Bloody stupid way to set latency if you ask me.

cheers

  • 2 years later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Mixing things up - installed some leather recaros to match the leather seat covered rear seats. Interior looks pretty schmick now except for some slight wear on the steering wheel which I will monitor and address if it becomes worse or actually noticeable!  
    • Didnt realise RB's had more then 1 head.
    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
×
×
  • Create New...