Jump to content
SAU Community

Recommended Posts

OK, so I have been trying to get this rb25 neo running for a couple of weeks now. I've done all the wiring myself and I'm about 98% sure its all done properly.

i have fuel pressure, pump is wired to 12v constant through relay.(actually spikes way up to about 100psi)

new tomei fuel pressure regulator.

listened to the injectors with long screwdriver while turning the CAS and they're all clicking.

pulled the coil-packs out, and with the spark plugs in them i turned the CAS. there's spark.

I re-checked the cam timing, and its bang on.

ive tried to start with maf unplugged. nothing.

tried to start with ICV unplugged. nothing.

installed fresh spark plugs after them getting fouled

so im running out of ideas.. the engine cranks from the starter turning, but it doesnt even try to start. any ideas from anyone of what i could try next??

the rb25 is from a r34 GTT.

One thing i noticed was the TPS has 6 wires going to it. in two sets of 3, one set is black red and white which is connected. and the other set of 3 is brown yellow and green which isn't connected to anything and aprears to blacked of from the factory.(looks like and oem blanking plug)

2012-08-17203407.jpg

2012-08-17203423.jpg

Link to comment
https://www.sau.com.au/forums/topic/407277-rb25-neo-wont-start-r32-swap/
Share on other sites

how would i go about doing that? just by adjusting the FPR? what if i didnt have an adjustable one? when the tomei FPR was on my rb20 i have is adjusted for 35psi and havnt adjusted it since. why would it be higher now?

A given flow through a restrictive orifice will increase if the flow is increased but the orifice is not.

The reg doesn't know how much fuel you want. It only knows how much resistance to create. If you increase the flow of fuel by increasing the size of the pump or replacing the pump, the pressure will increase because the reg still creates the same resistance

It's a stupid question, but hey, you wouldn't be the first - is the fuel connected to the rail correctly? Stick a pressure gauge in the inlet side of the rail.

Are the coils and injectors firing in the correct order?

Do you have compression?

What ECU are you using?

Have you got a good battery to start the engine with?

Elite, that makes sense. ill dial down the pressure then to compensate for the extra flow from now running 12v constant at the pump. good thing i have the adjustable FPR then or i wouldn't be able to do that. ill go with 35 psi.

Elk, the fuel lines are hooked up correctly. i have a pressure gauge installed in the feed line constantly and another fuel pressure gauge inside cabin. i have pressure. i have great compression, did a dry compression test while i tested for spark and it was 160~170 on all 6 cylinders. i believe im using a r34 GTT ecu part number # 23710-AA500. and my battery has 12v. i keep it on a trickle charge at night.

how would i check to see if the coils and injectors are firing in the correct order? and if its wrong, how would i fix it? the CAS can only be installed the one way..so it couldn't be that.

A given flow through a restrictive orifice will increase if the flow is increased but the orifice is not.

The reg doesn't know how much fuel you want. It only knows how much resistance to create. If you increase the flow of fuel by increasing the size of the pump or replacing the pump, the pressure will increase because the reg still creates the same resistance

Actually, the definition of a pressure regulator is that it is actually set to a given pressure, not a set restriction size. That is how they actually work as a regulator. if it was a fixed orifice, then upstream pressure would yo-yo as the demand went up and down.

On that basis, if you were to take a pressure reg from an RB20 with a small fuel pump and put it on an RB25 with a big fuel pump, then provided the reg was actually big enough* to flow the required amount of fuel back to the tank, it should run at exactly the same pressure as it did before.

*and being an aftermarket adjustable reg intended for use on arbitrary engine/pump combos, you would expect it to be big enough.

Nevertheless, if the pressure is set too high, then follow Dan's advice and wind it back down to something sensible.

how would i check to see if the coils and injectors are firing in the correct order? and if its wrong, how would i fix it?

Your OP suggested that it is a custom wiring job. You will need to have the injectors and coils removed from their fittings when you spin the CAS. They should activate in the firing order 1-5-3-6-2-4. If they don't fire in that order, re-wire the loom. (Stick the injectors in a bucket or similar to catch the petrol. You could also try and observe the spray pattern of each injector.)

If, on the other hand, you have used a factory loom, then it should all connect up correctly.

the CAS can only be installed the one way..so it couldn't be that.

If the locating tab in the end of the exhaust cam is broken, then it is possible to put the CAS in in about 10 different ways.

ya elk, its a factory loom. the only parts i messed about with was connecting the loom to the chassis plugs.

does anyone here have an r34 GTT? just to check how many relays are on the engine loom near the ecu. because on mine there is only one 6 pin brown relay. maybe i am missing a start relay or something (although there are no wires that aren't connected)

Kiwi, its not the mitsubishi one, it has a plastic cover. looks like the r34 one. pretty sure its not r33. and its making the injectors click, and spark plugs spark. so should be fine i think

DVS, i thought that could be the issue as well, but when i took the CAS off to check, the slot it actually off centered. so it can only go on the one way.

GTS, if its just the one brown ECCS relay then im good. it clicks when i plug it in with ignition set to ON.

what would i be looking for with the timing light while cranking the engine?

sooo there is definitely something fishy going on with the fueling system.

- i turned the FPR max each way and it didnt even change the pressure at all.

- i removed the fuel pump fuze and cranked the engine to see if the pressure would drop and it doesn't even budge.( injectors arent spitting?)

- and with a hunch i removed the return line going to the FPR and its bone dry!... there much be a blockage inside the rail somewhere? probably before the injectors.

http://www.youtube.com/watch?v=gABQmtQiDPk&feature=youtu.be

what should i do from here? does this mean i have to remove my intake mani and access the fuel rail?? :( I've done it before, but what a pain in the ***

Edited by amnash

Are you absolutely sure you have the lines around the correct way? The R34 fuel rails have pressure dampeners on both sides of the rail as well as the factory pressure regulator. If you feed fuel in reverse, it will show pressure on that gauge because you have it on the feed side but the reg won't work in reverse. Just try swapping the fuel lines around mate. It sounds exactly like it by your description

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Brooooo Please send ABS control unit schematic Please! R33 gts25t ABS (Its two plug ecu, black and white) wire colors possible? [email protected]
    • Don't even try to run it on the stock ECU if you're going to have the boost controller bring boost above ~10 psi. I've already told you that. If you use the Nistune ECU, you will need to CAREFULLY read the available documentation for Neo tuning, and read some threads on the Nistune forums, to discover the various things you have to do to prevent the ECU from going bananas when the boost is too high. The is a table associated with th boost sensor that must be modified to prevent it from shitting the bed. This is just one of the things that you will need to do to the tune in Nistune, because the Neo turbo ECU will be expecting to see a number of things (such as the TCS) that are not there, and you have to block the DTCs on those. It is totally not surprising to me that you are having the problems that you are, but the solutions to these problems have been known for >15 years. So just get it done.
    • Hi. Sry iam not a mechanic and iam not at the car atm so i dont know 100% but they told they measure those and even try to change those. AFM they have two. Coils are new a they have my old one too. Plugs too. ECU...we have 25 NEO stock and Nistune 25 NEO.   But i dont know if any one those could be the problem and why/if/what can cause this, Only thing they did not check is fuel...but that walbro 255 is new(like 1,5 years)... That fuel pressure gauge idk...but i let them know Any suggestions?   EDIT: how can they know if it is like you say he ECU pull power when it reaches a specific boost level that is too high? Tha car has boost controler
    • Can you clarify what you mean by boost cut, do you mean it misfires both when under load (driving) and when stationary and out of gear? Or does the ECU pull power when it reaches a specific boost level that is too high (boost control issue)? Does it occur at idle with no throttle? When you say "the ECU is OK", what ECU is it and why do you think it is OK? Have you used the NEO ECU, and if so do you have a MAP sensor attached? Same for the AFM, why do you think it is OK? Do you have any way to put a fuel pressure gauge on it (even just a mechanical one between the fuel filter and fuel rail)?
×
×
  • Create New...