Jump to content
SAU Community

Recommended Posts

Hey guys long story short i have changed my radiator , thermostat , radiator hoses , radiator cap and water pump and since then my overflow bottle has gone bone dry 2 times and im freaking out as i have checked my oil cap and its not milky and the fact that i have basically changed the whole cooling system and this is happening.

has anyone else had this same problem or know what it could be cos from what iv seen i cant see any coolant leaking.

last time i filled it up when the overflow went empty, now yesterday the coolant had about 2 fingers left in the bottle and i had a looktoday and there is nothing left then i went filled petrol and have not checked the radiator yet

long story short i bought this car and it sat for 1 year as i was still on my ps and when i was getting a power steering belt changed i later on realised something must of hit the standard radiator and there was a hole so i swapped it out for a just jap one. upon getting my fulls i got it tuned there was a hairline crack in the water pump so that was swapped out and i thought id might as well do the thermostat as the rest of the cooling system was new

hey you bleed the cooling system of air... it could be just bleeding the air from the system and using the coolant from the overflow like it should.

cheers sam

system was bled and filled up after so i doubt it could be that.

If its not leaking on the ground then its probably going in a cylinder,most probably a head gasket.Check the spark plugs,if ones a bit chalky then thats the cylinder

coming to think of it i have had a really bad misfiring on idle so i will def give the spark plugs a check tomorrow

Could be air still working itself through the system keep on filling up and hope it stops, give it 5 more cold start-ups to be sure.

This happened to me, more then twice when i went for a drive checked the coolant in the morning and nothing was in the overflow

turned out my radiator cap was shot and no pressure was in my hoses (check for pressure in yours) changed it and 2-3 times after that it did the same

thing just not as bad and i just kept on feeling her up until coolant stayed. I reckon air still in the system ! i was afraid my head gasket or worse

cracked block was the problem, thank god it wasn't.

Edited by starwarz

poppedd in to my mechanics today he is leaning towards a air leak as when he put more fuel into the tune the car started to idle better.

so its going in next monday for a smoke test and a pressure test on the cooling system

thanks mate... this is the last thing i need now haha.. had car in lock up for a yr just watching it till i got my fulls and hopefully i dont need to watch it for another yr till i save $ to build the engine

It still needs bleeding there hard to bleed. I keep bleeding it then let it cool down and check overflow bottle until level stablizes takes close to 10 times til fully bled so nothing to worry about, either keep topping it up til it stops losing or bleed it.

Edited by boostn0199
  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So I actually had the cover off my car today, here is a (bad) pic of the setup. I have an oil cooler thermostat block, the temp sender is straight in there. The pressure sender has a short AN line to a T piece which is mounted (hopefully cable tied counts as mounted....) on the chassis. BTW every fitting you could ever imagine exists....just depends what they cost and how many you need. Raceworx AN adapters are here: https://raceworks.com.au/fittings/adapters/, I think you said you need BSPT to AN (https://raceworks.com.au/fittings/adapters/bsp/tapered/an-to-bspt-adapters/) and AN to NPT (https://raceworks.com.au/fittings/adapters/npt/) BTW, braided line is super simple to make. It looks intimidating, is not.
    • Perfect day for a pie, really needs a soft top in this weather though
    • Prime parking, she is a little girl...LOL
    • I'm actually not sure - I think it was "Stealth Performance" (It really is near impossible to find a FEMALE 1/8BSPT to 1/8NPT male at ALL) but having the thing leveraged on a 90 degree angle on a small aluminium fitting is not too smart. Also in not too smart, I've drilled out the center of the broken fitting so there's maybe 0.00001mm of thread to bite into, so yeah. I may have to get it drilled/tapped/plugged entirely. Given I could conceivably tap a thread/adapter/pressure line in any point in the oil system I suppose it's feasible to run a line to the Nissan Sensor to keep the dash working. Do these exist in AN fittings and the like? Like an AN fitting that has a NPT (or other?) thread as well for putting a sensor in?
    • I would agree.  There will be an amount of boost you could run safely with an otherwise factory system, but it would be low enough to not be worth the cost.  And if you are reliving your 20s, you know a 'little bit' was never enough. Personally, if I didn't want to spend the money, then stick with NA bolt-ons, and maybe a tune.
×
×
  • Create New...