Jump to content
SAU Community

Recommended Posts

Hey guys long story short i have changed my radiator , thermostat , radiator hoses , radiator cap and water pump and since then my overflow bottle has gone bone dry 2 times and im freaking out as i have checked my oil cap and its not milky and the fact that i have basically changed the whole cooling system and this is happening.

has anyone else had this same problem or know what it could be cos from what iv seen i cant see any coolant leaking.

last time i filled it up when the overflow went empty, now yesterday the coolant had about 2 fingers left in the bottle and i had a looktoday and there is nothing left then i went filled petrol and have not checked the radiator yet

long story short i bought this car and it sat for 1 year as i was still on my ps and when i was getting a power steering belt changed i later on realised something must of hit the standard radiator and there was a hole so i swapped it out for a just jap one. upon getting my fulls i got it tuned there was a hairline crack in the water pump so that was swapped out and i thought id might as well do the thermostat as the rest of the cooling system was new

hey you bleed the cooling system of air... it could be just bleeding the air from the system and using the coolant from the overflow like it should.

cheers sam

system was bled and filled up after so i doubt it could be that.

If its not leaking on the ground then its probably going in a cylinder,most probably a head gasket.Check the spark plugs,if ones a bit chalky then thats the cylinder

coming to think of it i have had a really bad misfiring on idle so i will def give the spark plugs a check tomorrow

Could be air still working itself through the system keep on filling up and hope it stops, give it 5 more cold start-ups to be sure.

This happened to me, more then twice when i went for a drive checked the coolant in the morning and nothing was in the overflow

turned out my radiator cap was shot and no pressure was in my hoses (check for pressure in yours) changed it and 2-3 times after that it did the same

thing just not as bad and i just kept on feeling her up until coolant stayed. I reckon air still in the system ! i was afraid my head gasket or worse

cracked block was the problem, thank god it wasn't.

Edited by starwarz

poppedd in to my mechanics today he is leaning towards a air leak as when he put more fuel into the tune the car started to idle better.

so its going in next monday for a smoke test and a pressure test on the cooling system

thanks mate... this is the last thing i need now haha.. had car in lock up for a yr just watching it till i got my fulls and hopefully i dont need to watch it for another yr till i save $ to build the engine

It still needs bleeding there hard to bleed. I keep bleeding it then let it cool down and check overflow bottle until level stablizes takes close to 10 times til fully bled so nothing to worry about, either keep topping it up til it stops losing or bleed it.

Edited by boostn0199
  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Need to see other side of PCB in that area...ie; I don't see any thru-hole mounting, just soldered vias (smd zeners in SOT23 have 3 legs but only 2 are used, as reflected by PCB tracks)
    • 4 to 5 is fine. It will be slow, but that's better than blowing turbos. I don't have a PS pump idle up solenoid on my car, because... I think when we put the Neo in we retained my R32 lines. But.... From inspecton of the R34 vacuum hose diagram, you can see that the solenoid needs to be connected to the turbo inlet as source of clean air) and the plenum (as source of vacuum - which is the place for the air to flow to to cause the idle to increase). So 3 to 1 is VERY WRONG. 3 should go to either the turbo inlet, or the plenum. Follow the other hose from the PS solenoid and if it goes to the plenum, then your 3 goes to 2 2 would also serve as a bleed port for a boost solenoid.
    • Pull them out and pull more apart. You can't do shit with them still bolted to the floor of the car.
    • Yes it is. ZD1 is on the other side of the board. Where ZD1 is marked is clearly opposite a 2 pin device. Our 3 pin device here is not a ZD.
    • Alright, a little update on this... I called Fulcrum, who used to be the distributor in Australia. No Bueno, they don't service them anymore.  Called shock works, who don't service them but offered to dyno the shocks for performance, and suggested DNA in Sydney might service them.  Called DNA, who also do not service them and basically said they try to steer customers away from tein for this exact reason these days- there is just no support for them anymore apparently.  Both SW and DNA said they are a not necessarily a bad product, but they just don't service the brand or know anyone who does service the brand anymore.  So... I could keep calling around but at this point I think I'll probably just spring for the shockworks product, unless anyone here knows anything.  Cheers 🍻 
×
×
  • Create New...