Jump to content
SAU Community

Recommended Posts

Not sludgy at all motor is fine the turbo line is blocked

so you're saying it is blocked? seen a few cars with turbo oil starvation problems, usually blocked lines/filters if it has them, it's getting oil in the exhaust after it seizes you mean?

Yeah I mean was running fine then the rear turbos exhaust wheel blew cos of shaft play it was hitting the inside of the turbo housing so I changed the turbo now it's make only 7 psi instea of 14 when I start it up only the front turbo spins freely at idle the rear one is hard to turn

the oil starvation will flog the turbo so the wheel will come into contact with the housing, if you disconnect the oil feed off the rear turbo and start it up you'll prob see no oil come out or the odd drop, you'll have to pull it apart and check and clean everything

If oil feedline blocks then it will seize while drain blocks will cause turbo to leak oil from all seals. It looks like the feed is blocked. Check the line and drill out the oil restrictor in its fittings.

wont be oil drain, its 4x the size of the feed.

feed will be blocked, meaning there is gunk elsewhere in the system most of the time... cause if there wasn't - how can it be blocked?

No I've got it all worked out if the turbo was seizing it wouldn't make boost its only making 0.6 bar so I'd say it's leaking somewhere one of the pipes meant to be 1 bar And now it's smoking like a bitch on boost I compression tested it and my results where this 50 55 75 100 100 125

Im sorry Ash, I've tried to stay out of this thread.

Your compression is wwwwwaaaaaayyyyyy f**ked.

Your motor has most likely sucked 1 of the 3 turbo's you have gone through.

You say you have it all figured out? I dont think you do. You need to go and buy another motor from the wreckers, this time you need to

  • Make sure you have a good fuel pump
  • Make sure you have working turbo's
  • Make sure you compression test the motor prior to dropping it in
  • Go and get a tune (for the love of god)
  • Don't come on here and ask for advice then turn around and say NO I have it all worked out. (very frustrating when you offer advice and it gets thrown in your face!)

No I've got it all worked out if the turbo was seizing it wouldn't make boost its only making 0.6 bar so I'd say it's leaking somewhere one of the pipes meant to be 1 bar And now it's smoking like a bitch on boost I compression tested it and my results where this 50 55 75 100 100 125

So you had the same problem back in July? Or is this a new compression problem?

http://www.skylinesaustralia.com/forums/topic/404483-rb26-melting-pistons/

If it's a NEW compression problem i would suggest

1. Getting a better tune

2. Learning how to drive

3. Selling the car all together

now it's smoking like a bitch on boost I compression tested it and my results where this 50 55 75 100 100 125

after reading some of your posts I have to ask, how exactly did you go about doing the comp test ?

you say the rear turbo is the one that keeps blowing but the front 3 cylinders have the lower comp

Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • There are several aftermarket options available, from not-too-painful moneyhttps://justjap.com/collections/driveshafts-bearings/products/d-max-reinforced-replacement-rear-driveshaft-set-fits-nissan-s13-s14-s15-r32-r33-r34-c35 and  https://justjap.com/products/crank-motorsport-billet-rear-axles-fits-nissan-skyline-r33-gts-t-r34-gt-t?srsltid=AfmBOorQk4xkGUa98kO7v2ePLUiNt-HRrM2AwWNw9mbSIVE1ujBVwY__, all the way up to The Driveshaft Shop https://driveshaftshop.com/skyline-cv-axles/
    • Yeah based on old XRC5964S specs, it looks to be roughly GTX3576R sized? But this 5964S compressor will flow 90lb airflow somewhat similar to the compressors in both the GTX3584RS or G35-1050.. I fully expected the 0.64 rear A/R to choke up top - seems way too small from typical convention - but these are seemingly beneficial over the prior 0.82 results.. Be interesting to see if he comments on the EFR question in that thread - he mentioned in a prior video that BW EFR's were the "cats pajamas 10 years ago", but by the sounds of things all his kits have been using Xona for quite a while now.
    • Yeah it’s still got the oem manual gearbox and clutch, only kinda mods are a blow off valve, coil overs, and a aftermarket intercooler. Also had it for about 2 months now with a lovely midnight purple paint on it.
    • Yeeeppp, been following a lot of the testing on the latest Xona stuff and there are some mental results.  He also went over 1000hp @ 4 hubs on his Mainline with a XRE6364S (63mm) which was also well into the 20psi range before 4000rpm on a 2.5. Crazy stuff. Fwiw the XRE5964S is basically the modern equivalent of their old HTA3582 - would drive nicely enough on an RB25 or 26, but proven capable of a huge amount of power if you want to spicy with rpm tho even at sane boost levels will make stout numbers 
    • The axels in my R33 seem tired, and have a bit of play in them. I cannot find any new of course, not interested in buying used, but I am looking to see if anyone can identify some cross compatible axles. In the states I have seen suggested for S chassis the J30 axles, however for the skyline (as best I can tell) the lengths are about an inch off (2.5cm) on both sides. R33 my measure L 22" R 24.5" GPT L 22.5" 24.25" J30 L 23.5" 25.5"  so shaft length is probably an inch wider. Not sure if someone has another still remanufactured option besides the J30. I figured worst case I can buy a pair tear them down and swap the center shaft. My other option was reaching out to GSP to see if they cannot piece together a set, since the axle stubs are still manufactured, I wouldn't think it be that hard to find a shaft or make a shaft work. 
×
×
  • Create New...