Jump to content
SAU Community

Recommended Posts

Here is my pride and joy for expressing of interest at this moment. 1993 model in Burgundy colour.

KMs: 113000kms.

Mods:

2860-5 turbos

Walbro fuel pump

Nismo 600cc injectors

splitfire coilpacks

HKS camgears

grex oil cooler

Trust oil sump.

tomei oil restrictors

Power FC with hand controller

HKS boost controller

Extreme twin plate clutch

Original Nismo seats in perfect condition.

Alloy radiator.

Custom made oil catch can by Silverwater Automotive

Carbon shielded airbox

Nismo N1 headlights with HID kit installed.

Brand new Optima AGM dry cell battery with 800cca just put in.

HPI clear timing belt cover.

Braided water and oil lines on turbos.

Atezza switch between AWD and RWD

The bad:

Dash light is on and off which might be bad connection behind. I haven't really had time to take it out to check.

No A/C, condensor was taken out to fit the large oil cooler.

The car is in very good condition for an r32. Not a single bit of rust underbody, in the boot or in the engine bay, or even on any panels. Interior wise, a little wear and tear on steering wheel and shift boot. Dash condition is immaculate with absolutely no bubbles on the passenger side. Car is dead straight and drives dead straight.

Power: 330awkw @ 21psi on high boost

309awkw @ 19psi on low boost

Note: Power made with gtr AFMs. But they are at their max so Z32 AFMs are the option for more power out of this setup.

No asking price as this is a pure EOI. Offers are welcome.

Photos:

Photos:

264766_10151013675541121_799001671_n.jpg

319458_10151018188741121_1461797509_n.jpg

377090_10151018189726121_367795330_n.jpg

Edited by G0Z1LLAAAAA34
Link to comment
https://www.sau.com.au/forums/topic/409736-syd-1993-r32-gtr-~eoi~/
Share on other sites

Opps forgot to add:

Genuine Bilstein coilovers

Nismo front pipes followed by 3 inch cat back

Large 2 piece front brake rotors (Brand unknown, they came with the car when I bought it)

More technical bit:

Knock: 25-35 shown on FC hand controller on high boost setting

Injector max duty: 68-70% under full power on high boost setting

Edited by G0Z1LLAAAAA34

oops, you also forgot to add the price

read the rules

I don't know if you understand what express of interest means......This isn't an official for sale add so no price needed in the thread.

He is asking $16500 on JDMST.

And I don't know which GTR you are referring to. Read my jdmst thread again and see if there is a price on it....

Did you tell him he's dreaming?

I don't know what dreams you are having but i am certainly awake if you haven't noticed :)

Edited by G0Z1LLAAAAA34

No money owing. No major accidents. The chassis is accident free. I think a couple of panels have been repainted before I purchased the car as we can expect from a r32 gtr this age.

Edited by G0Z1LLAAAAA34
Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • ok so if i wanted to go 18's i would go for 8's  in front 30+ or 32+ off set at front and the back 9 would be ok? what offset should i aim for.. then can i do some  hunting for wheel rim choices..    If i get this - will this fit all around: Size: 18 x 8.5 +37 - n what tyres size tyre should i get for front n back?  
    • Absolute f*cking nightmare. I had to take breaks constantly, and I was always pissed off when I got home. The line split in Italy on day 2 (we drove from the Netherlands), lol. Driving any narrow European town was... well, sh*t.   Appreciate it man. Here, I'll just drop a favourite from the load I took on Saturday.   I'll update here when things happen with the car, the thing is, with stock power and almost everything chassis-wise taken care of, there really are no problems. 268,000kms now and counting.  
    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
×
×
  • Create New...