Jump to content
SAU Community

Recommended Posts

  • Replies 262
  • Created
  • Last Reply

Top Posters In This Topic

Entered for everything :D

Ummmm let me go check the thread.

Timetable for the day is as follows;

Gates open: 7:00am

Sign on starts: ~7:30am

Scrutineering starts: 7:30am

Scrutineering finish: 8:30am

Drivers briefing: 8:45am (Attendance mandatory, no driving otherwise)

Sessions start: 9:00am

Sessions finish: 5:00pm

Gates close: 5:30pm

So probably 6:30 I guess?

Link to comment
https://www.sau.com.au/forums/topic/410670-sau-nats/page/9/#findComment-6621131
Share on other sites

Same for Saturday?? Cause I'll be going drifting so will probs still cruise down with everyone only pulling the bash line

Drifting? Where? I'm not going up on Saturday or Sunday anymore just the friday

Link to comment
https://www.sau.com.au/forums/topic/410670-sau-nats/page/9/#findComment-6621340
Share on other sites

Woohoo!!! Don't think I'm working on Friday, so I may well be in to cruise up & watch some mad Skoyloin Ection!!!

About time I met up with all of you Nissan Freaks Awesome peoples. Can't wait. It's gonna be sweeeet.

So what's the plan for meetups?

Is it 7am at the servo at the showground on Fri, Sat and Sunday?

Edited by Not a Pulsar
Link to comment
https://www.sau.com.au/forums/topic/410670-sau-nats/page/9/#findComment-6621617
Share on other sites

Hows 8.30am from Gungahlin ? It's just over an hour.

See you at 8.15am at that servo

Will have to wait in line as I expect a few hundred Skylines in the SnS

Edit: Could even meet up at one of the rest stops on Lake George if others are comming.

Happy to meet at that new servo where Maccas is on Fed Hwy. I'll be there from 8, leaving at 8:30 :)

Link to comment
https://www.sau.com.au/forums/topic/410670-sau-nats/page/9/#findComment-6621921
Share on other sites

I keep forgetting that the track day is tomorrow and it's airstrip runs on Saturday (which honestly I don't care THAT much for) so I'll be heading up probably around lunchtime Saturday or whenever I could be f**ked. Still debating whether I come up in the van and sleep in the back after the dinner, or if I drive the 33 up then home again Saturday night then BACK AGAIN Sunday morning in the van.

Either way, my Skyline isn't going anywhere near the Show n Shine lol

Link to comment
https://www.sau.com.au/forums/topic/410670-sau-nats/page/9/#findComment-6625221
Share on other sites

Some of us need to leave a bit earlier, 4.30 up to prep the car and leave by 6am is a bitch.

Why not pack the car tonight so you dont have to get up so early?

I keep forgetting that the track day is tomorrow and it's airstrip runs on Saturday (which honestly I don't care THAT much for) so I'll be heading up probably around lunchtime Saturday or whenever I could be f**ked. Still debating whether I come up in the van and sleep in the back after the dinner, or if I drive the 33 up then home again Saturday night then BACK AGAIN Sunday morning in the van.

Either way, my Skyline isn't going anywhere near the Show n Shine lol

Why no show and shine for the 33?

Link to comment
https://www.sau.com.au/forums/topic/410670-sau-nats/page/9/#findComment-6625235
Share on other sites

Why not pack the car tonight so you dont have to get up so early?

Why no show and shine for the 33?

Because it's a disgusting example. Haven't washed it in a touch over a month, and will be stretched for time before weekend so I doubt it has a chance at receiving anything more than a shitty DIY booth wash. Engine bay needs degrease and clean. Interior need a vacuum BADLY.

Pretty much it's an embarrassing car.

Link to comment
https://www.sau.com.au/forums/topic/410670-sau-nats/page/9/#findComment-6625412
Share on other sites

well someone should volunteer to do all of that for the chance to drive it! lol im giving mine a wash tonight but there is also another car wash its going to get tomorrow afternoon.

Capital Mens Club bikini car wash 3-6 tomorrow!

$30 per car with $5 going to councer council! im sold!

Link to comment
https://www.sau.com.au/forums/topic/410670-sau-nats/page/9/#findComment-6625505
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • You’ll be very upset when you bust that too not to mention the gearing totally sucks. Don’t do it.
    • Is the panel filter one that is oiled? Have you ever cleaned or touched the AFM?
    • So.... the K&N air box thingo was too big, ended up gifting it to a mate, well, by gifting it he actually supplied food and beer at the pub,  which was nice, as it will not sit on a shelf in the garage for the next 10 years I did trim up some of the existing stuff to neaten it all up and gave it some wrinkle paint, unfortunately it currently has a used and abused mish mash of different types of hose clamps, 4 big fat T bolt type (shit), and a few normal clamps of vairing sizes and brands, but..... only until the 6 constant tension black worm clamps that I ordered from EFI solutions turn up next week Currently the current hose clamps are triggering me hard, LOL Is this the final version, probably not, I really want just 2 silicone pieces, a straight bit of silicone from the filter to the MAF is easy and will happen as soon as I head into Just Jap tomorrow, the problematic part is a 30° silicone bend from the MAF to the TB that I can connect the engine breather from the head, I found that there are bulk head fittings for boat bilge pumps that should work, but until I can get a 30° silicone bend the alloy pipe, and the 11ty thousand hose clamps, are there for the foreseeable future 4 hose clamps are golden, 6 are grudgingly acceptable, the 8 currently holding it all together is just taking the piss    I've also ordered 60 more retaining wall blocks for the front yard, I mis-gonculated the height that was required to get above the base of the Photinia's (red robin's) that are the hedge behind the front fence, currently it is 2 blocks high, and about 1/2 a block short, so going 3 blocks high will be above the base of the red robin's, and allow some room for mulch
    • It is the stock air box with the panel filter. Everything else is stock except the exhaust at this point, as I also went back to the cleaned 270cc injectors. I will check the RPM when the IACV is unplugged and report back.
    • As MBS suggested if this is happening when the engine is cold you're going to want to remove the intake air regulator and verify resistance + that the shutter is physically opening and closing. At -20C should be fully open, 20C half open, over 60C fully closed. At 20C should be 70-80 ohms. For AAC valve testing using a Consult cable see if you can raise and lower the idle by commanding more or less AAC duty cycle. Hopefully it's pretty linear as well, shouldn't be like 30% AAC valve is barely idling and 40% is 1500 rpm.
×
×
  • Create New...