Jump to content
SAU Community

Recommended Posts

  • Replies 76
  • Created
  • Last Reply

Top Posters In This Topic

how many litres are you calling a tank? the tank is 65L, but fuel light generally comes on with 10L to go. is the fuel light coming on before you fill up?

as i say in every fuel economy thread, unless you are running it until it runs out of fuel, using "a tank" as a measure for economy is stupid. given that people will all fill up at different points on the gauge, the economy you are getting compared to others will vary by a fair bit.

still worth taking note of how many litres went in, because if it has an aftermarket fuel pump then they sometimes don't sit as low as the stock pumps and can make you run out of fuel well before the fuel light has even come on.

check you don't have a leak in the cooler piping somewhere. it probably has a large leak somewhere which is making it leak a heap of boost and making it run rich.

do you have an aftermarket boost gauge? if so, where does it sit when you are just idling? should sit about -20 at idle if there is no leaks

I'm sorry that I'm not being very helpful with my problem. And I do and it does sit right on -20

I would give more details but I'm new to it all and don't understand it to well, it's just getting too overwhelming.

Edited by Ausdogga

Ok, sorry,

Ill start again, fuel Econ it up the shitter getting 277k per tank on 98,

It won't hold revs changing gears or it they drop quicker by braking, I do have shit on my black bar, and a backfire at times I'm guessing burning the exsess fuel from it running rich,can be very very unresponsive and almost stall at times if I take off slowly, when I boost at times it will go to 11 then drop to 8 or 9 when I have it set at 10. I think that's it. :/ apart from that its all stock only running 10 pound,

Edited by Ausdogga

how's your water temp? perhaps your thermostat is cactus, also is your water temp sensor plugged in?

There's a chance the car is always thinking it's cold and dumping in loads of fuel. Unplug the water temp sensor and see if there's a difference, I had this problem before when I forgot to plug back the water temp sensor when I pulled the injectors out of my fridge.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
    • How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
×
×
  • Create New...