Jump to content
SAU Community

Recommended Posts

Recently had a track day and managed to blow a manifold gasket, upgraded to a steel gasket and put the car back together.

took it for a drive to make sure she was running right and it runs terrible, hesitating coughin when boost starts to come on. sort of like the coil packs are shafted but ive only replaced them about 3 weeks ago.

any body got any ideas?????

Link to comment
https://www.sau.com.au/forums/topic/411659-rb25-breaking-down/
Share on other sites

exaust gasket, its not blowing any smoke that i can see, i got fuji spark coil packs as it is a budget car at the moment, but i checked coilpacks last night and there all fine so i changed plugs and still runs like ass.

ive narrowed it down to a "boost leak" but question is how to i find it??

I think I've heard of Fuji coilpacks before, someone else put them on and they were misfiring straight out the box or soemthing.

Although I just found the link, the person in question actually had one of their new coilpacks die: http://www.skylinesaustralia.com/forums/topic/407220-help-r34-rb25de-changed-coil-packs-ran-well-for-approx-40kms-then-started-misfiring-again/

ive checked coils and there all good i ve checked for leaks and could find nothing at all, i am ganna pull the turbo off tonight and check for cracks. i am startin to think there might be a crack in the waste gate maybe..

how are you coming to the conclusion that the coils are all good?

Just because they look fine doesnt necessarily mean that they are fine...

Had a friend who bought yellowjackets barnd new have them fail after 3 months. 'Looked fine' still tho...

ok thats a good start n fair enough

But you say in the OP that the issue is when you are driving it and coming on boost.

So while the coilpacks might be able to work fine at idle they might still be having issues under load. Which is of course their usual point of issue- under load, coming onto boost and in particular at 4500rpm WOT....

sounds a lot like a boost leak, just because it does it coming on boost doesn't mean it's coilpacks

the pipe can be holding together enough which lets the car idle and drive off boost but when you put some pressure there it the leak opens up and cause your issue, sounds like a silicon hose joint not done up properly

I changed the turbo last night to make sure there wasnt any cracks or leaks, re gaped sparkies to .6. Ive checked and checked for leaks. The car runs rough as guts on idle. Doing a compression test tomorrow just to make sure then will start the elimination process again

There would have to be a fair bit of oil to be getting past the rings to make it run rough as guts, it would also be chugging out white smoke. Best to rule out the coils being he problem first.

With those compression numbers a rebuild would be on the horizon but it doesn't mean you shouldn't properly diagnose the problem first.

A good way to check the coils is just to have a look at night with the car idling, usually the bad one will arc a bit giving you a little flash of light, but my rb20 was doing the same thing, kept trying different things, spark plugs and gaps, but it just turned out to be the coils, when I had vacuum leaks it would usually start missing much earlier than what yours seems to be.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Who did you have do the installation? I actually know someone who is VERY familiar with the AVS gear. The main point of contact though would be your installer.   Where are you based in NZ?
    • Look, realistically, those are some fairly chunky connectors and wires so it is a reasonably fair bet that that loom was involved in the redirection of the fuel pump and/or ECU/ignition power for the immobiliser. It's also fair to be that the new immobiliser is essentially the same thing as the old one, and so it probably needs the same stuff done to make it do what it has to do. Given that you are talking about a car that no-one else here is familiar with (I mean your exact car) and an alarm that I've never heard of before and so probably not many others are familiar with, and that some wire monkey has been messing with it out of our sight, it seems reasonable that the wire monkey should be fixing this.
    • Wheel alignment immediately. Not "when I get around to it". And further to what Duncan said - you cannot just put camber arms on and shorten them. You will introduce bump steer far in excess of what the car had with stock arms. You need adjustable tension arms and they need to be shortened also. The simplest approach is to shorten them the same % as the stock ones. This will not be correct or optimal, but it will be better than any other guess. The correct way to set the lengths of both arms is to use a properly built/set up bump steer gauge and trial and error the adjustments until you hit the camber you need and want and have minimum bump steer in the range of motion that the wheel is expected to travel. And what Duncan said about toe is also very true. And you cannot change the camber arm without also affecting toe. So when you have adjustable arms on the back of a Skyline, the car either needs to go to a talented wheel aligner (not your local tyre shop dropout), or you need to be able to do this stuff yourself at home. Guess which approach I have taken? I have built my own gear for camber, toe and bump steer measurement and I do all this on the flattest bit of concrete I have, with some shims under the tyres on one side to level the car.
    • Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
×
×
  • Create New...