Jump to content
SAU Community

Favour - Borrow Some R32 Coilpacks That Are Known To Work


Recommended Posts

I'm in a bit of a bind, I have new coilpacks and a miss fire at 4000rpm that screams coilpacks. Does anybody SE have a spare set of known to be working r32 coils I could chuck in to test?

*sigh*

I'm in a bit of a bind, I have new coilpacks and a miss fire at 4000rpm that screams coilpacks. Does anybody SE have a spare set of known to be working r32 coils I could chuck in to test?

*sigh*

I got my stockies but they were misfiring after a long drive :(

I'm sure some of them would still be good although not sure which one...

Let me know

Could it possibly be the coilpack loom? I've known a few times this to be the cause too

They go all hard a crispy after heating up so much after time, and some of the clips break etc

Told Dave to check it few times, he said it's basically at same age as his coilpacks which is a year old or so.

Think he's trying bcpre7s plugs next.

Your problem may well lie somewhere here. 7s are possibly too cold, try some 6s.

He's having issues with 6s at the moment gapped with 0.8mm

He had 1.1 gap that was misfiring, changed to 0.8, same story.

He've tried another coilpacks, igniter to no avail. Dave has put up a thread on forced induction with detailed problem.

Yeah i'm not trying to be difficult and be obscure, there is another thread (although i'm open to more ideas tbh this is killing me).

It's a misfire at 4000rpm under load when hot. Boost is 14psi. Car has been running fine, misfire appeared towards end of 5000km service interval so I assumed it was just old plugs which were 1.1 gapped. After replacing with 0.8mm gap it hasn't gone away.

It definitely isn't coilpacks, igniter. I am confident it isn't the loom it's new and not old and shitty like many I have owned that I had troubles with.

Gap, can try going back to 1.1 except everyone is certain that 0.8 should reduce misfire problems...

So that leaves me with fuel pressure (I have an 044 intank which could have packed up and given up, they arent' meant to be mounted intank). My workshop has recommended i check the pressure at idle.

Charge air measurement (haven't had any issues with these AFM yet but it could be one of them being a prick). I can check this with consult.

if it isn't those two things, i'm scared, and out of ideas ;). Thanks for your all your suggestions.

i only had misfire when car was hot and revving above 4000rpm. Just like how you described. Removed coilpacks, inspected and looked visually fine. (no cracks etc). Mechanics were telling me its not coilpacks either.

Ended up replacing with brand new splitfires and problem was gone.

Unless you have tested with a brand new set of coilpacks, i wouldnt rule them out just yet...

I tested with a set of splitfires from one of my other skylines that is currently driving around just fine. Not sure you can get a better test of coilpacks? Not only that but these coilpacks are literally new genuine nissan units... really hard to believe it is the coilpacks.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Have you confirmed its the actual axles? Also the wheel bearings that mount on the hubs to hold the axles wear out. I replaced mine as they got play in them. It sorted my play issue. 
    • Ive converted a few clusters for the R33 with 320km/h dials. On the back there are some pads which can be bridged or unbridged (using solder or wick braid) to calibrate it. There is one bridge which is for MPH <> KPH; and there are combinations of bridges to offset it. There is probably a diagram  For example; this is my conversion for a 180km/h dial to a 320km/h dial (I put custom GT-R dials on it with the GTS25t layout) If you have J2 soldered (assuming the S clusters have a similar config to the R clusters); you may need to remove that solder
    • Back on topic 😉, these are some of the notable pages from the booklets that are supplied with each weekly parts update. I never knew the BNR32 test mule car had an S13 Silvia body...
    • This. A 3d wheel alignment is like $120...just take it to the shop. Since theres probably multiple adjustments that need to be made after changing something. Mine has front/rear lower arms, traction rods, tension rods, camber arms, toe arms, front upper arms, hicas kit, sway bars and coilovers. I measure from the edge of the bolt holes on the originals and set the same length on all the adjustable stuff to dial it as close as I could to OEM. Took it straight for alignment; it didnt feel right at all...after alignment, it feels perfect. Similarly i've just changed the springs on another car; and I still needed multiple adjustments to bring it back in spec.
    • A full Veilside kitted JZA80 Supra in Meriken park in Kobe city a few weeks back
×
×
  • Create New...