Jump to content
SAU Community

Recommended Posts

So looking at putting coolant my skyline because it getting hot when using only water (coolant leaked then I replaced it with water, hence the heating issue, as there was no issues before when I was running coolant).

Can someone recommend a coolant they have used or a coolant you would advise NOT to use. I have heard organic coolant is good, you basically buy a small bottle then add it to the water in your radiator, anyone used this? I believe it's similar but a bit different to antifreeze/antiboil. Any ideas suggestion advice etc is appreciated, cheers!

Link to comment
https://www.sau.com.au/forums/topic/413769-which-coolant/
Share on other sites

I use Genuine Subaru (Castrol) Anti-Freeze/Boil coolant. Only cause I get them free ;)

I wouldn't use cheap $5 coolant from Supercheap. From my general knowledge, if you use a coolant that isn't antiboil rated, what happens if it boils? it creates pressure and could crack your rad. I could be wrong, but just my opinion. Just use a decent Castrol Anti Freeze/Boil coolant and you'll be fine.

Link to comment
https://www.sau.com.au/forums/topic/413769-which-coolant/#findComment-6626548
Share on other sites

Thanks everyone. I've noticed it's been "using" water (I fill up the water then after a while of driving I notice the temp goes up and check the radiator and it's quite low, it's happened twice now, first time I thought I didn't fill it up enough and there was air bubbles). I can't see any leeks anywhere even when it's hot. At first I thought because it was only water not coolant it was evaporating once hot (maybe out of the radiator cap as it was hissing when the car gets hot) but that's not even possible is it? Any ideas on what it could be?

Link to comment
https://www.sau.com.au/forums/topic/413769-which-coolant/#findComment-6626625
Share on other sites

Thanks everyone. I've noticed it's been "using" water (I fill up the water then after a while of driving I notice the temp goes up and check the radiator and it's quite low, it's happened twice now, first time I thought I didn't fill it up enough and there was air bubbles). I can't see any leeks anywhere even when it's hot. At first I thought because it was only water not coolant it was evaporating once hot (maybe out of the radiator cap as it was hissing when the car gets hot) but that's not even possible is it? Any ideas on what it could be?

I've also been told not to use water since it can create rust or algae (in the reservoir) in extreme circumstances, UNLESS it's distilled water. But then again, just don't use it. We have coolant for a reason.

Did you do a proper bleed? If not there may be air bubbles sitting at the high points of the motor. if you drain the coolant completely, it would take about 7.5 Liters (well for my RB25DE Neo in R34 does anyway) to fill it up. If you did a proper bleed then your radiator most likely has hairline cracks in it and only leaks when your driving at 60KM + when coolant is heated up, creates pressure and forces the hairline crack open and seeps out. Doesn't do it when its idle or off since its cooler then and less pressure.

It happened to me before and I changed the rad, no problems anymore

Link to comment
https://www.sau.com.au/forums/topic/413769-which-coolant/#findComment-6626759
Share on other sites

Nissan long life coolant can't go wrong

^^ this ! nissan LLC is in concentrated form when you buy it from nissan, when you add the recommended amount of distilled water to it it works out to be good value too

Link to comment
https://www.sau.com.au/forums/topic/413769-which-coolant/#findComment-6627269
Share on other sites

Awesome I'm gonna try the bleeding the water/coolant too, didn't know there was the bleed valve near the plenum lol, I'm also gonna run the heater. Maybe a dumb question but does autobarn or supercheap sell nissan LLC? Or am I gonna have to go to nissan?

Link to comment
https://www.sau.com.au/forums/topic/413769-which-coolant/#findComment-6627272
Share on other sites

My stock HCR32 was filled with water when I got it, don't know how long it was in there, but it didn't have any effect on engine temperature, has never been over 85 C and that's while monitoring through consult whist going for a thrash. Have since drained and replaced with the Nissan coolant and temps are the same.

Link to comment
https://www.sau.com.au/forums/topic/413769-which-coolant/#findComment-6627298
Share on other sites

My stock HCR32 was filled with water when I got it, don't know how long it was in there, but it didn't have any effect on engine temperature, has never been over 85 C and that's while monitoring through consult whist going for a thrash. Have since drained and replaced with the Nissan coolant and temps are the same.

Plenty of people run pure water with no issues.

Link to comment
https://www.sau.com.au/forums/topic/413769-which-coolant/#findComment-6627519
Share on other sites

im surprised people run just water and havent had too many problems.

Water boils, then evaporates, thats one of the reasons of coolant its anti-freeze and anti-boil

Doesnt freeze over at cool temps and Doesnt boil like a kettle at hot temps

For a few bucks, it gives you peace of mind.

Link to comment
https://www.sau.com.au/forums/topic/413769-which-coolant/#findComment-6627913
Share on other sites

I was always told. Most 'coolants' are actually an anti freeze(ethylene glycol) and lower the boiling temperature of water. In warmer climates you can get away with just running distilled water and a corrosion inhibitor

I have been doing this for years with no issues, its only like $6 for the inhibitor too! Apparently ethylene glycol can catch fire if you have a high content mix and it sprays over a hot exhaust manifold or similar..

Link to comment
https://www.sau.com.au/forums/topic/413769-which-coolant/#findComment-6627980
Share on other sites

im surprised people run just water and havent had too many problems.

Water boils, then evaporates, thats one of the reasons of coolant its anti-freeze and anti-boil

Doesnt freeze over at cool temps and Doesnt boil like a kettle at hot temps

For a few bucks, it gives you peace of mind.

You water temp. would only sit around the 80 degree area anyway. Even if the water temp. reaches 100 degrees the pressure in the cooling system raises the boiling point.

This is why it's important to replace old radiator caps that don't hold the right pressure anymore.

Link to comment
https://www.sau.com.au/forums/topic/413769-which-coolant/#findComment-6628115
Share on other sites

^^^i would be suprised if this was the case for long. . .even distilled water will cause corrosion/ironise on an iron block RB

Do a bit if searching on the forum, it's been talked about plenty if times.

And as for temp issues, no there is no temp issues running just water. As said by someone else, the increased pressure in the system raises the boiling point. Generally cars run about 1 bar of pressue in the system, meaning the boiling point if water is over 120 degrees.

. The majority of coolants are only corrosion inhibitiors, and sometimes anti-freeze. You can still boil the coolant at about 100 degrees if you have a faulty cap.

Link to comment
https://www.sau.com.au/forums/topic/413769-which-coolant/#findComment-6628661
Share on other sites

Do a bit if searching on the forum, it's been talked about plenty if times.

And as for temp issues, no there is no temp issues running just water. As said by someone else, the increased pressure in the system raises the boiling point. Generally cars run about 1 bar of pressue in the system, meaning the boiling point if water is over 120 degrees.

. The majority of coolants are only corrosion inhibitiors, and sometimes anti-freeze. You can still boil the coolant at about 100 degrees if you have a faulty cap.

No doubt it has been "talked about" i tried running (only)distilled water in my rb and a week later it started to go brown, no doubt corrosion between the iron block and the water hence why corrosion inhibitors are used by the factory, if they could get away without the expense/necessity of using it they would
Link to comment
https://www.sau.com.au/forums/topic/413769-which-coolant/#findComment-6629188
Share on other sites

I have been doing this for years with no issues, its only like $6 for the inhibitor too! Apparently ethylene glycol can catch fire if you have a high content mix and it sprays over a hot exhaust manifold or similar..

Its smokey and the distinctive smell of burning coolant goes everywhere, but thats about it.

Link to comment
https://www.sau.com.au/forums/topic/413769-which-coolant/#findComment-6629222
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Sounds like you've got an interesting adventure ahead here with local support if you have trouble! My guess is that, unboosted, you will be OK with a small upgrade like -9. What will happen is that once the stock ECU sees more airflow than it expects it will add a heap of fuel and pull a heap of timing to be safe because it can't understand how it could get that much air without there being an issue. You will see clouds of black smoke and it won't pull hard through the midrange and top end. So, overall it will be a bit frustrating but should be OK. If you are still nervous set the base timing back 2o through the CAS, but it will be even more sluggish everywhere. As said above through...this is not my guarantee your engine won't be blown into a million pieces, leaving you looking for very hard to find parts A better idea is get a computer with logging ASAP, wire in a wide band O2 sensor and a use remote tuner. I've done multiple cars this way and while it is not as good as a specific tune on a dyno they can get it 90% right. I'd suggest if you can afford an R33 GTR these days you can afford an ECU and tune. And if you can't afford that you sure won't be able to afford the rebuild if it goes bad in the meantime,.  
    • Yeah it would be nice if someone took the time to put that sort of information together, but there are a lot of variations in looms. I think you are making this way hard for yourself if you just want to get it running....sourcing an SR20 with the right wiring will be a billion times easier than matching the RB loom to an S15 chassis. If you do end up going this way, you just need to trace every wire in the loom with a multimeter, 95% of them will go to a location you can confirm at the ECU.....and then post it up for the next person who needs it  
    • Just top it up with water, and keep a general idea of how much you added. It is normal for water to be pushed into and pulled out of the reservoir through the cap, and it should not be more than half full or it will be likely to overflow when hot. Any decent mechanic can do a pressure test of the cooling system to confirm if you have a leak. Keep in mind if it is only leaking a little and when hot it may well evaporate before you see it hit the ground
    • I'd ask the shop what they used and use that. Mixing coolants is sometimes OK, sometimes not, and you have know the details of each coolant to know whether it's a good idea or not.
    • Is it alright to top up with just another green coolant?
×
×
  • Create New...