Jump to content
SAU Community

Recommended Posts

  • Replies 71
  • Created
  • Last Reply

Top Posters In This Topic

I am also in the ulleh group, sorry I meant ching chong, I mean yellow group.

WIll install pod filter in place of the factory airbox Saturday morning for maximum flutters ROFL

think cause i was so early in my rego like december last year i got first group :( should have held off :( oh well ill show up all the comadores and falcons for u guys lol

represent, make sure you get the flutters going LOL

Well had a great day, in the last session of the south circuit on the last lap she sprung a small coolant leak in the bypass cooling hose under manifold.

Great day good instructors best fun ive had with pants on. My first proper race track experience.

if you got your times recorded on the texi would love to see the results.

My quickest was a 32.23sec in the GTSt :) only got 4 runs.

awesome day, motorkhana was alot of fun, my quickest was 32.04, circuit was very good, had bit of brake fade on the hairpin and got in before the rain started

ran the car with stock actuator boost as a pre-caution in case i got carried away 1st time on track

both instructors were very good, heaps of information and pointers

+1

Had a great day - fun/non serious atmosphere, loads of variety of cars. Very nice BB BNR34 GTR in the last session.

Besides the "speed limit" I did manage to get up to a sneaky 140km/h down the back bit. Instructor was great - very informative and calm. Instilled a good level of confidence and level headedness. Motor held up fine - bloody over engineered the cooling system so the thermos didn't even switch on. Brake pads were the first thing to start to go, but only had a long pedal a couple of times over the sessions. Pity the traffic was so heavy. Would have liked to have at least one good timed session, but was stuck behind quite a bit of traffic.

Motorkhana times- I did 4 runs.

RWD: first lap - 33.82 then 31.82

Put the fuse back in so AWD

30.38 and best time of 29.67 before I pulled aside.

Got a bit of a round a of applause from the timing crew, so I don't think many were below 30 secs. Hope they put the times up, but don't think they were officially recorded. Only other sub 30 sec time I heard was an Audi quattro wagon. Wagon FTW!

All in all a great day!

good job, yah on my track runs my instructor said "that Sti infront isnt sticking to 100km/h, just go as fast as you can' so i managed about 135 up that main straight before the esses. was loads of fun, got to pass 3 cars in my 2 sessions.

The best pass was on a vt SS vommadore, all over him through the corners but struggled a little to keep up on staights but was waved through and left him behind on the next few laps. No brake fade the Bendix held up well. Just the slight issue of coolant but got her home no overheating at all. good old Skylines ;)

Yeah it was good fun. Rained during our track session so that made it pretty wild even with 4wd... Civic in front of me had a wild lift off oversteer spin after the sweeper down to the old turn 9; ended up off the track to the inside and not far off the wall.

Only got 4 runs on the motorkhana too and managed a 28.8 (got video of that run so I might post it up later - using the horn is key)

I did a 46 on my second last run !! haha

Was stuck on the spot and couldn't even get past the first cone, I said to the guy next to me this place is suddenly very slippery while I did like 5 donuts, clutched in and motor was still revving :/, throttle linkage must have gotten caught when I clutch kicked.

He said you better stop before we get in trouble, hahah he loved it

I am disappoint!

Blew a cooler hose off on the last session of the motorkhana and didn't realise till i went onto the track for the first session...so had to crawl around and make my way back into the pits to fix it. Coach was great though, (Bob) even helped me fix it. Went out again for the second sesh and lasted almost one lap before it popped again!

Fixed it once more and headed home...have now fixed the problem hose. Guess i should have done some more testing with the new cooler setup before hitting the track.

My quickest khana lap was 31.02. Pretty happy with that.

Gah! Beaten by a R34 GTR! Suppose thats ok ;)

Yeah, we were watching the last track session, and looked very slippery. Michael, I think your car is set up for drift! Had to creep round the turn near the pits to get around it!

edit- I reckon I could do that time if I had a handbrake. Have a stupid footbrake is useless, and I suffered massively for it.




  • Latest Posts

    • So I mentioned the apprentice, @LachyK helped take the bonnet off. We just undid the nuts on the hinges and unclipped the gas struts, then pulled the bonnet back a little as the front was catching on the front bar.  I had a good look at everything today and have removed the rams, repaired/reset the hinges and bolted it back together like it never happened. I'll do a separate write up on the repair, and I also removed the poppers from the Fuga today too to save grief down the road.....as said above it is at least $5k to repair retail. I'm also happier about my ability to prepare a race car, and less happy about Nis-nault's engineering (I can hear @GTSBoy sAfrican Americaning) because the top hose of the radiator didn't slip off.......it snapped clean off. By practice I put the hose clamp hard up against the flare on a neck to make it least likely to ever move (thanks @Neil!). I guess that puts a little more pressure on the end of the pipe as it is further away from the rad, but still, that is pretty shit. I've put it back on for now as there was a fair bit of neck still there, but obviously there is no lip on the neck any more so I don't think I'll track it again until I have a new rad. Speaking of which....more research required. It looks like Koyo makes a standard size radiator in ally which I'll grab in the meantime, but I really want something thicker so might have to go custom in the medium term (ouch) Coolant still needs a refill and I have the pressure tester on it over night, but other than a wash down of the engine bay it seems alright. And @MBS206 noted something noisy on the front of the engine and I think I agree....time for a new accessory belt and tensioners I think.
    • our good friends at nismo make a diff for it, I have one (and a spare housing to put the centre in) on the way. https://www.nismo.co.jp/products/web_catalogue/lsd/mechanical_lsd_v37.html AMS also make a helical one, but I prefer mechanical for track use in 2wd (I do run a quaife in the front, but not rear of the R32)
    • What are we supposed to be seeing in the photo of the steering angle sensor? The outer housing doesn't turn, right? All the action is on the inside. The real test here is whether or not your car has had the steering put back together by a butcher. When the steering is centred (and we're not caring about the wheel too much here, we're talking about the front wheels, parallel, facing front) then you should have an absolutely even number of turns from centre to left lock and centre to right lock. If there is any difference at all then perhaps the thing has been put back together wrongly, either the steering wheel put on one spline (or more!) off, and the alignment bodged to straighteb the wheel, or the opposite where something silly was done underneath and the wheel put back on crooked to compensate. Nut there isn't actually much evidence that you have such a problem anyway. It is something you can easily measure and test for to find out though. My money is still on the HICAS CU not driving the PS solenoid with the proper PWM signal required to lighten the load at lower speed. If it were me, I would be putting either a multimeter or oscilloscope onto the solenoid terminals and taking it for a drive, looking for the voltage to change. The PWM signal is 0v, 12V, 0V, 12v with ...obviously...modulated pulse width. You should see that as an average voltage somewhere between 0V and 12V, and it should vary with speed. An handheld oscilloscope would be the better tool for this, because they are definitely good enough but there's no telling if any cheap shit multimeter that people have lying around are good enough. You can also directly interfere with the solenoid. If you wire up a little voltage divider with variable resistor on it, and hook the PS solenoid direct to 12V through that, you can manually adjust the voltage to the solenoid and you should be able to make it go ligheter and heavier. If you cannot, then the problem is either the solenoid itself dead, or your description of the steering being "tight" (which I have just been assuming you mean "heavy") could be that you have a mechanical problem in the steering and there is heaps of resistance to movement.
    • Little update  I have shimmed the solenoid on the rack today following Keep it Reets video on YouTube. However my steering is still tight. I have this showing on Nisscan, my steering angle sensor was the closest to 0 degrees (I could get it to 0 degrees by small little tweaks, but the angle was way off centre? I can't figure this out for the life of me. I get no faults through Nisscan. 
    • The BES920 is like the Toyota Camrys of coffee machines. E61 group head is cool, however the time requirements for home use makes it less desirable. The Toyota Camry coffee machine runs twin boilers and also PID temp control, some say it produces coffees as good as an E61 group head machine.
×
×
  • Create New...