Jump to content
SAU Community

Recommended Posts

Looking at eoi at this stage. Not 100% sure if want to thorw anymore money at this car as ive already spent n ass load.

Blown bottom end (suspected spun bearings) happened the other week at SAU nats.

Spoken to JEM about this the other day, alot of the parts can be re used (potentialy just needs new crank n pistons)

Ok the basics of the car:

ive owned this for the last 5 years, it is always garaged

its only been driven twice a week since January this year. Has done 3300kms this year

Motor was originaly built 19/11/2009

fuel system built 21/7/2010

gearbox built 27/9/2010 by award diff & gear box

tyres and rims January this year

here is some of the basic parts, full detailed list of every part on the car can be provided to serious people

Performance metal craft 9l sump

nitto oil pump

nitto i-beam rods

cp pistons

ati balancer

arp head and main studs

nitto full gasket kit including 1,2mm head gasket

ported and polished head

hks step 2 springs

oversize valves

jun retainers

hks 272 10.25 cams

hks t51r spl non bb turbo

trust stainless manifold heat coated

full 4" custom exhuast

trust 60mm w/gate

100mm intercooler with hks piping

koyo radiator

grex 19 row oil cooler with relocation kit

sard 1000cc injectors

sard fuel rail

1 internal bosch 044 pump

2 external bosch 044 pumps

custom surge tank

all braided lines

weldon adj FRP

OS giken 5 speed gear set with strenghtend input shaft

Nismo super coppermix twin competition clutch

C's short shifter

Tein hr coilovers

whiteline front n rear sway bars

standard strut braces

b pillar brace

hicas lock bar

dba slotted rotors

ferrodo ds2500 pads

hel braided lines

Nismo ztune carbon bonnet

border carbon air ducts

carbon 400r front lip

trust side skirts

abflug carbon rear diffuser

bride replica front seats with matching door trims

heaps of gauges

nismo 320km speedo

custom bolt in half cage

carbon look dash

This package made 422kw @ 21psi on 98

Selling the car as is, no part outs or anything like that

There is no money owing on the car

rego until may 2013

i also heave a heap of spare parts and still have all the rear interior that will come with the car

PM me with your email address for pictures or look in my profile for a couple pics but they are abit old

Looking for $20,000 for everything

new bottom end + e85 will get you around 550+ kw

Link to comment
https://www.sau.com.au/forums/topic/414538-eoi-mnp-r33-gtr/
Share on other sites

if i keep it, going 2.8l, already priced up and can be done for 15k or less if you take out things i was planning on that arnt realy needed

so for 35k or less you can have a 550+kw street gtr.

alot better then the stuff thats on car sales atm

paint is near perfect

carbon bonnet is painted mnp but vents have been left carbon

had previously run 10.9@ 129mph before current turbo set up ( can provide video proof)

some spares include standard bonnet

polished plenum

rear seats

all climate control

3 centre gauges

spare gear shift surround

red leather gear & handbrake boots

heaps of other stuff in the box

forgot to mention it runs a power fc djetro n blitz dual sbc boost controller

Link to comment
https://www.sau.com.au/forums/topic/414538-eoi-mnp-r33-gtr/#findComment-6643706
Share on other sites

Do you have the auction papers etc from Japan?

What auction grade was the car?

No mate I don't have any of that, I bought it already in Australia

Thanks Dave

Link to comment
https://www.sau.com.au/forums/topic/414538-eoi-mnp-r33-gtr/#findComment-6644199
Share on other sites

people please read the posts

NO SWAPS

i didnt write this just for the sake of writing something, i dont care what you have, i dont want it

im after cash sale only! i already have another car

Link to comment
https://www.sau.com.au/forums/topic/414538-eoi-mnp-r33-gtr/#findComment-6648039
Share on other sites

all pm's replied

if you dont have close to what im asking then dont pm me with low ball offers. and no 15k is not close

may consider removing carbon bonnet, rear diffuser, front lip, gauges if 20k is too much for you

( these parts alone cost nearly 4.5k)

Link to comment
https://www.sau.com.au/forums/topic/414538-eoi-mnp-r33-gtr/#findComment-6652759
Share on other sites

Ok people here is the deal

Im tried of getting different offers from people

so here is the only 2 options

20k for everything exactly how it is

OR

15k minus bonnet (standard will be put back on), no front lip, no rear diffuser, no head lights (u will need to get your own) and no gauges (stock 3 gauges and climate control will be put back in)

these are the only 2 options

Link to comment
https://www.sau.com.au/forums/topic/414538-eoi-mnp-r33-gtr/#findComment-6653119
Share on other sites

Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • Power is fed to the ECU when the ignition switch is switched to IGN, at terminal 58. That same wire also connects to the ECCS relay to provide both the coil power and the contact side. When the ECU sees power at 58 it switches 16 to earth, which pulls the ECCS relay on, which feeds main power into the ECU and also to a bunch of other things. None of this is directly involved in the fuel pump - it just has to happen first. The ECU will pull terminal 18 to earth when it wants the fuel pump to run. This allows the fuel pump relay to pull in, which switches power on into the rest of the fuel pump control equipment. The fuel pump control regulator is controlled from terminal 104 on the ECU and is switched high or low depending on whether the ECU thinks the pump needs to run high or low. (I don't know which way around that is, and it really doesn't matter right now). The fuel pump control reg is really just a resistor that controls how the power through the pump goes to earth. Either straight to earth, or via the resistor. This part doesn't matter much to us today. The power to the fuel pump relay comes from one of the switched wires from the IGN switch and fusebox that is not shown off to the left of this page. That power runs the fuel pump relay coil and a number of other engine peripherals. Those peripherals don't really matter. All that matters is that there should be power available at the relay when the key is in the right position. At least - I think it's switched. If it's not switched, then power will be there all the time. Either way, if you don't have power there when you need it (ie, key on) then it won't work. The input-output switching side of the relay gains its power from a line similar (but not the same as) the one that feeds the ECU. SO I presume that is switched. Again, if there is not power there when you need it, then you have to look upstream. And... the upshot of all that? There is no "ground" at the fuel pump relay. Where you say: and say that pin 1 Black/Pink is ground, that is not true. The ECU trigger is AF73, is black/pink, and is the "ground". When the ECU says it is. The Blue/White wire is the "constant" 12V to power the relay's coil. And when I say "constant", I mean it may well only be on when the key is on. As I said above. So, when the ECU says not to be running the pump (which is any time after about 3s of switching on, with no crank signal or engine speed yet), then you should see 12V at both 1 and 2. Because the 12V will be all the way up to the ECU terminal 18, waiting to be switched to ground. When the ECU switches the fuel pump on, then AF73 should go to ~0V, having been switched to ground and the voltage drop now occurring over the relay coil. 3 & 5 are easy. 5 is the other "constant" 12V, that may or may not be constant but will very much want to be there when the key is on. Same as above. 3 goes to the pump. There should never be 12V visible at 3 unless the relay is pulled in. As to where the immobiliser might have been spliced into all this.... It will either have to be on wire AF70 or AF71, whichever is most accessible near the alarm. Given that all those wires run from the engine bay fusebox or the ECU, via the driver's area to the rear of the car, it could really be either. AF70 will be the same colour from the appropriate fuse all the way to the pump. If it has been cut and is dangling, you should be able to see that  in that area somewhere. Same with AF71.   You really should be able to force the pump to run. Just jump 12V onto AF72 and it should go. That will prove that the pump itself is willing to go along with you when you sort out the upstream. You really should be able to force the fuel pump relay on. Just short AF73 to earth when the key is on. If the pump runs, then the relay is fine, and all the power up to both inputs on the relay is fine. If it doesn't run (and given that you checked the relay itself actually works) then one or both of AF70 and AF71 are not bringing power to the game.
    • @PranK can you elaborate further on the Colorlock Dye? The website has a lot of options. I'm sure you've done all the research. I have old genuine leather seats that I have bought various refurbing creams and such, but never a dye. Any info on how long it lasts? Does it wash out? Is it a hassle? What product do I actually need? Am I just buying this kit and following the steps the page advises or something else? https://www.colourlockaustralia.com.au/colourlock-leather-repair-kit-dye.html
    • These going to fit over the big brakes? I'd be reeeeeeeeaaaall hesitant to believe so.
    • The leather work properly stunned me. Again, I am thankful that the leather was in such good condition. I'm not sure what the indent is at the top of the passenger seat. Like somebody was sitting in it with a golf ball between their shoulders. The wheels are more grey than silver now and missing a lot of gloss.  Here's one with nice silver wheels.
    • It's amazing how well the works on the leather seats. Looks mint. Looking forward to see how you go with the wheels. They do suit the car! Gutter rash is easy to fix, but I'm curious about getting the colour done.
×
×
  • Create New...