Jump to content
SAU Community

Recommended Posts

sorry man I cant help. But you have the guys who will sort it out

sounds like you may have to re-visit the install of the GB and have another look at the clutch :/

new gearbox or new to you ? State of the clutch ?

After thought, heard a few guys chatting last night. What about electricals/sensors..

New to me, seems fine. I can go through all the gears with no problems as long as I don't hit boost.

The clutch has only done around 10,000km as my mate (same guy) changed it when I installed a new engine.

Prior to this it was working perfectly.

All the sensors were all plugged back in and were in better condition than they were on my old box.

Were the sensors put back in the correct spots.

Are they coloured ? and do they carry different voltage signals ?

I could be totally wrong as seriously I don't know what I'm talking about - lol

just listening to a different conversation...

I think we may have discovered the problem.


On the new box, the front cover shaft was welded back on in the past and we think that the weld isnt allowing the
thrust bearing to go back far enough resulting in the slipping of the clutch (driving like the clutch pedal is half pressed in)

So now I need to try and source the part number to get a new one as the one on my old box has snapped off.

Thanks anyway Richard :)

Trying to keep the bottom list short, but its hard.

"Love the beast" or compulsive modifyer?



Done

big fmic

new kingpin bearings

rb 25 turbo

3" exh w bell dump

one piece tailshaft

podfilter & cold air box

strut braces front and rear

Neomax adjustable coilovers

adj upper arms front and rear

DW tracton rods

Hardrace radius rods

DW hicas eliminator

solid cradle bushes

solid steering bush

oil catch can

thermo fans

Autometer oil, water, fuel/air, boost guages

voltmeter

volt stabilizer

yellow jacket coilpacks

stereo, amp and speakers

new parcel shelf

approved child seat strap mount

rear view camera

sports steering wheel

immobiliser

engine damper

heavy duty clutch

battery in boot

oil cooler and filter relocation w thermostat

removed aircon

Nismo shift knob

electric heater

GTR front bar w n1 vents

Nistune ecu

cam gears

timing belt

water pump

rear wiper delete



To Do

fix harmonic balance

tap temp switch hole

fix intercooler piping

fix immobiliser light bezel

fix pod & cold air box

radiator and oil cooler ducting

braided brake & clutch lines

fire extinguisher

fuel pump

injectors

z32 afm

tune


pwr steering cooler

improve head lights

boxes in boot

heatsheilds

dash

fuel cooler

diff centre?

good thermofan

drivers seat

use stickers

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Thank you, 100% the intent. New coils were due and the 17" sixers look/feel loads better than the stock wheels. The aero options are so spot on.   Thanks for the warm welcome, all!
    • 98 r34 gtt Been rocking my latest setup and car running like never before. Have put a good 200 miles on it since all the latest changes and additions. everything is dialed in and have been driving it a bunch.   However, all a sudden last weekend as soon as I pushed throttle passed 4k and the engine stumbles, (slow or fast acceleration) hesitates and doesn’t go above 4100 or so, like a misfire. Everything else seems fine. I had a “good” set of coil packs that I removed from car when I first got it when I changed them over to new coils. I swapped out current ones for those, but no change. I also changed the plugs, no change. Seems to rev over 4 when out of gear with no load just fine no “misfire”, but as soon as its in gear with a load of any kind, it “misfires” as soon as rpm drop back below 4 k it runs perfectly, smooth, starts, restarts and drives fine as long as I keep it below 4 k while in gear. All readings look fine, no CEL   Any idea as to what could all a sudden cause an issue when pushing rpms passed 4 k?
    • When you say your cams are 272/262 is that 272in and 262ex?
    • We're arguing semantics. I am saying 45 accel and a 55 deccel ramp are "2 ways". Even a 45 degree ramp and an 89 degree ramp is "2 ways", because it is literally... two ways. The cusco 55/30 ramp is a 2 way. It's two ways. I get it though - in normal nomenclature a "2 way" would be 45/45 or 55/55 or 60/60 i.e the same locking in both directions. And something like 45/65 would be considered "1.5 way". I would then say if we're getting into the nitty gritty then every locking diff is a "2 way" diff and we should not speak in 1.5, or 2 ways but ramp angles instead. Which ofc if one of those ramp angles is 90deg, that side is not doing any locking. :p So Nismo don't obviously sell 3 things. The fact of the matter that they only sell two items really goes to show that there's a 2 way and a "1,5 way" which is really a 1 way. I believe the actual lockup for the 'adjustability' of the GT pro is really just setting preload for when the ramps actually start locking up. It's not changing how much 'wayness' there is. It is (somehow) horribly explained. People just buy whatever diff and go "locks up good bruh" and that's what ends up on socials forever.  
×
×
  • Create New...