Jump to content
SAU Community

Recommended Posts

sorry man I cant help. But you have the guys who will sort it out

sounds like you may have to re-visit the install of the GB and have another look at the clutch :/

new gearbox or new to you ? State of the clutch ?

After thought, heard a few guys chatting last night. What about electricals/sensors..

New to me, seems fine. I can go through all the gears with no problems as long as I don't hit boost.

The clutch has only done around 10,000km as my mate (same guy) changed it when I installed a new engine.

Prior to this it was working perfectly.

All the sensors were all plugged back in and were in better condition than they were on my old box.

Were the sensors put back in the correct spots.

Are they coloured ? and do they carry different voltage signals ?

I could be totally wrong as seriously I don't know what I'm talking about - lol

just listening to a different conversation...

I think we may have discovered the problem.


On the new box, the front cover shaft was welded back on in the past and we think that the weld isnt allowing the
thrust bearing to go back far enough resulting in the slipping of the clutch (driving like the clutch pedal is half pressed in)

So now I need to try and source the part number to get a new one as the one on my old box has snapped off.

Thanks anyway Richard :)

Trying to keep the bottom list short, but its hard.

"Love the beast" or compulsive modifyer?



Done

big fmic

new kingpin bearings

rb 25 turbo

3" exh w bell dump

one piece tailshaft

podfilter & cold air box

strut braces front and rear

Neomax adjustable coilovers

adj upper arms front and rear

DW tracton rods

Hardrace radius rods

DW hicas eliminator

solid cradle bushes

solid steering bush

oil catch can

thermo fans

Autometer oil, water, fuel/air, boost guages

voltmeter

volt stabilizer

yellow jacket coilpacks

stereo, amp and speakers

new parcel shelf

approved child seat strap mount

rear view camera

sports steering wheel

immobiliser

engine damper

heavy duty clutch

battery in boot

oil cooler and filter relocation w thermostat

removed aircon

Nismo shift knob

electric heater

GTR front bar w n1 vents

Nistune ecu

cam gears

timing belt

water pump

rear wiper delete



To Do

fix harmonic balance

tap temp switch hole

fix intercooler piping

fix immobiliser light bezel

fix pod & cold air box

radiator and oil cooler ducting

braided brake & clutch lines

fire extinguisher

fuel pump

injectors

z32 afm

tune


pwr steering cooler

improve head lights

boxes in boot

heatsheilds

dash

fuel cooler

diff centre?

good thermofan

drivers seat

use stickers

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Bah! I can't see the point in custom number plates at all. I went to the rego office, fished through a box of "premium" plates (the ones that had the "not as tall" option for the front plate) and picked the one that had a 32 in it. That's the limit of the effort and cost I will put into number plates. The only plate that I'd consider paying for would be 2332, but that's not possible here because it already exists from probably 90 years ago, and it would cost a fortune to obtain it, if it were available.
    • After chasing my tail with LS results..... and cheaper than a turbo swap... How confident are you that the dyno is accurate relative to other results? How fast is the car - What MPH does it actually run? Is this similar to what people running this power would expect?
    • Hi mate I am having an identical issue with my 98 R34 GTT. The engie suddenly cuts out under load at about 3-4k, black smoke out exhaust. Almost feels like traction control kicking in. No CEL but still going to check codes later today. Car was sitting in the shed for about 5 months before hand and only idled a few times, took her out with about 1/4 tank, filled up and thats when the issues started happening.  Threw on a spare set of coils/harness and checked plugs which was no help. Recently had fuel pump/filter changed so surely thats not the issue unless condensation in fuel, I just havent had the time to drain it It's running a hi flow turbo, bosch 1000cc injectors, walbro 450L, Z32, Nistune etc... All about 2000km old.
    • I always wonder where the obsession with legal/illegal spacing on number plates in the UK comes from. Because it comes up in comments in every UK-based video I see on youtube. From my point of view all of your plates look a bit odd. Just because there are no markings whatsoever. In Australia we have the state that has to be on it. In Europe you get stamps and state logos. Yours look a bit like a throwaway draft that people then stuck with. And attached with blu tack so that it falls off at the slightest disturbance. Not trying to hate, but it's interesting how things are done in different countries. Do you have to follow a lettering convention when choosing a custom plate?
    • Hybrid sounds like a supercharger... It's half a turbo, with a belt to drive it! Oh wait, they're just called super chargers...
×
×
  • Create New...