Jump to content
SAU Community

Recommended Posts

Ya laze kent.

Thnx for the info - just txt'd Kyle (K_D) that info

I can top your 4pk950 with a 4pk440ml

(Woodstocks burbs) Bahaha

Well soon anyway

:cheers:

Edited by Sinista32

What body kit is that on the 34?

CRUISE japan front bumper, modified impul gtt side skirts (I'll get a pic to show what I mean), impul rear bar, spoiler taken off and boot welded, r-tune (I think, or z-tune?) bonnet

As I mentioned, the front guards are gtr, while the rear guards have been flared close to 40mm from memory (I could run a 18x10.5 +15 rim with 265 rubber and no scraping)

GTR bodykit. Tome you should have told me you wanted the proper rear fenders i had two lying around the garage.

I was tempted to take those off your hands, but I figured I'd switch it up a bit and not do the full rear fender conversion.

I've never seen flared guards on a 34 in Aus, and because the guards remain metal I'm less scared they'll crack if I lower the car and run more aggressive wheels.

It can run very close to the same specs as a 34R in the rear now, but the bodywork itself remains more subtle looking.

Edited by TM7GTR

Blew another Passengers Headlight Bulb, found a spare but it's blown too.?. :( Checked fuses and all good.

Put in 2 cheaparse Ebay Ling longs to get me by...

When i go rb25, i will strip it down to nothing.

Then it will get the full treatment, stripping tar, spot welds, panel beating, paint job, new window rubbers, etc

Some things will not go back on. Most things to go, have been removed already.

Now i will start making stuff, i need to try and keep it simple.

And more research, looking at build threads, and planning.

When im good at welding, i can do yours too! And whoever else needs it.

Thinking about Grumblebee, could use a diifuser or two and skirt extensions.(from what i can see)

DIY welding bay

For all those bits n pieces that need welding on the car.

attachicon.gifDSCF2731.JPG

Now i have to practice.

When i can do alloy, i will be making a lot of stuff.

WHy you no buy welder from me?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Thank you, 100% the intent. New coils were due and the 17" sixers look/feel loads better than the stock wheels. The aero options are so spot on.   Thanks for the warm welcome, all!
    • 98 r34 gtt Been rocking my latest setup and car running like never before. Have put a good 200 miles on it since all the latest changes and additions. everything is dialed in and have been driving it a bunch.   However, all a sudden last weekend as soon as I pushed throttle passed 4k and the engine stumbles, (slow or fast acceleration) hesitates and doesn’t go above 4100 or so, like a misfire. Everything else seems fine. I had a “good” set of coil packs that I removed from car when I first got it when I changed them over to new coils. I swapped out current ones for those, but no change. I also changed the plugs, no change. Seems to rev over 4 when out of gear with no load just fine no “misfire”, but as soon as its in gear with a load of any kind, it “misfires” as soon as rpm drop back below 4 k it runs perfectly, smooth, starts, restarts and drives fine as long as I keep it below 4 k while in gear. All readings look fine, no CEL   Any idea as to what could all a sudden cause an issue when pushing rpms passed 4 k?
    • When you say your cams are 272/262 is that 272in and 262ex?
    • We're arguing semantics. I am saying 45 accel and a 55 deccel ramp are "2 ways". Even a 45 degree ramp and an 89 degree ramp is "2 ways", because it is literally... two ways. The cusco 55/30 ramp is a 2 way. It's two ways. I get it though - in normal nomenclature a "2 way" would be 45/45 or 55/55 or 60/60 i.e the same locking in both directions. And something like 45/65 would be considered "1.5 way". I would then say if we're getting into the nitty gritty then every locking diff is a "2 way" diff and we should not speak in 1.5, or 2 ways but ramp angles instead. Which ofc if one of those ramp angles is 90deg, that side is not doing any locking. :p So Nismo don't obviously sell 3 things. The fact of the matter that they only sell two items really goes to show that there's a 2 way and a "1,5 way" which is really a 1 way. I believe the actual lockup for the 'adjustability' of the GT pro is really just setting preload for when the ramps actually start locking up. It's not changing how much 'wayness' there is. It is (somehow) horribly explained. People just buy whatever diff and go "locks up good bruh" and that's what ends up on socials forever.  
×
×
  • Create New...