Jump to content
SAU Community

Recommended Posts

Small update.......

A friend / club member of mine had diagnosed an issue with the clutch cooling fan..........the clutch fan was moving within the cooling fan not from side to side but forwards and backwards.............needless to say it had to get fixed.

So I took that step today.

After much debate and swearing in three different languages I managed to remove the cooling / clutch fan without removing the radiator cooling shroud (yes it's all possible)

post-5053-13919376540164_thumb.jpg

I didn't go unsaved though

post-5053-1391937709587_thumb.jpg

Anyways me being the clean freak that I am, I thought Id give the cooling fan a clean down

post-5053-13919377773813_thumb.jpg

post-5053-13919377986855_thumb.jpg

Nice and dirty

post-5053-13919378408617_thumb.jpg

post-5053-13919378614121_thumb.jpg

post-5053-13919378828378_thumb.jpg

all clean :)

The next step was to install this little baby

post-5053-13919379339668_thumb.jpg

post-5053-13919379663435_thumb.jpg

Brand new clutch cooling fan

Thanks to Zac (Cowdy) for procuring this item for me so speedily

post-5053-13919380908618_thumb.jpg

post-5053-13919381024786_thumb.jpg

All fitted and ready to go back in its home ;)

That's it!

  • 4 weeks later...
If you want led's just get some eBay spec white led t10's they work a treat

You can get like 20 for $5

I got some the other day Zac.post-5053-13943455093535_thumb.jpg

post-5053-13943448288205_thumb.jpg

Can't wait to see what it looks like. But should that little much more brighter :)

Been busy paint stripping the rear bumper

post-5053-13943460057865_thumb.jpg anyone know how to remove the paint from the bottom bit? It's rough like the front bumper lip so very difficult to remove cleanly.

Also thought I'd tackled the shit spot welding on the back RHS rear quarter panel

post-5053-13943476985964_thumb.jpg

post-5053-13943477457016_thumb.jpg

All smoothed out with my trusty powerfile

Next will be a little sanding and then I will paint the rear panel in crystal white to make it nice and clean ;)

  • Like 1

Are you going to do anything with the spot welds you grinder back? Wouldn't be much straight left in the welds, if there's any weld left. I can't tell exactly where it is on the car. Thought about some stainless rivets, or rewelding it completely?

Are you going to do anything with the spot welds you grinder back? Wouldn't be much straight left in the welds, if there's any weld left. I can't tell exactly where it is on the car. Thought about some stainless rivets, or rewelding it completely?
strength*
Are you going to do anything with the spot welds you grinder back? Wouldn't be much straight left in the welds, if there's any weld left. I can't tell exactly where it is on the car. Thought about some stainless rivets, or rewelding it completely?
nah mate, the way theses spot welds have been applied is pretty full on and there is enough of it left on the car to keep everything nice and strong.

Should I feel the need for more bracing I would spot weld the entire car but it's not necessary...........for now

Spent all day at work reading this start to finish. Amazing. So awesome to see people like you restoring cars and spending so much money for nothing but the best! Love it! One day i'll own a '94 32 GTR V Spec II but for now, my Evo 8 MR will do :P

Keep up the good work!

Will get some LEDs for the reverse lights as well attachicon.gifImageUploadedBySAU Community1394346759.691514.jpg they are E4's by the looks of it

ive just done all the LED in my car Ants. PM me if you need the exact globe....

Spent all day at work reading this start to finish. Amazing. So awesome to see people like you restoring cars and spending so much money for nothing but the best! Love it! One day i'll own a '94 32 GTR V Spec II but for now, my Evo 8 MR will do :P

Keep up the good work!

thank you very much mate. It's comments like this ^ that keep me going.

There are lots of good bits indeed.

But just a little correction it's not a V-spec it's just a late 94 model GTR :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • This is where I share pain with you, @Duncan. The move to change so many cooling system pieces to plastic is a killer! Plastic end tanks and a few plastic hose flanges on my car's fail after so little time.  Curious about the need for a bigger rad, is that just for long sessions in the summer or because the car generally needs more cooling?
    • So, that is it! It is a pretty expensive process with the ATF costing 50-100 per 5 litres, and a mechanic will probably charge plenty because they don't want to do it. Still, considering how dirty my fluid was at 120,000klm I think it would be worth doing more like every 80,000 to keep the trans happy, they are very expensive to replace. The job is not that hard if you have the specialist tools so you can save a bit of money and do it yourself!
    • OK, onto filling. So I don't really have any pics, but will describe the process as best I can. The USDM workshop manual also covers it from TM-285 onwards. First, make sure the drain plug (17mm) is snug. Not too tight yet because it is coming off again. Note it does have a copper washer that you could replace or anneal (heat up with a blow torch) to seal nicely. Remove the fill plug, which has an inhex (I think it was 6mm but didn't check). Then, screw in the fill fitting, making sure it has a suitable o-ring (mine came without but I think it is meant to be supplied). It is important that you only screw it in hand tight. I didn't get a good pic of it, but the fill plug leads to a tube about 70mm long inside the transmission. This sets the factory level for fluid in the trans (above the join line for the pan!) and will take about 3l to fill. You then need to connect your fluid pump to the fitting via a hose, and pump in whatever amount of fluid you removed (maybe 3 litres, in my case 7 litres). If you put in more than 3l, it will spill out when you remove the fitting, so do quickly and with a drain pan underneath. Once you have pumped in the required amount of clean ATF, you start the engine and run it for 3 minutes to let the fluid circulate. Don't run it longer and if possible check the fluid temp is under 40oC (Ecutek shows Auto Trans Fluid temp now, or you could use an infrared temp gun on the bottom of the pan). The manual stresses the bit about fluid temperature because it expands when hot an might result in an underfil. So from here, the factory manual says to do the "spill and fill" again, and I did. That is, put an oil pan under the drain plug and undo it with a 17mm spanner, then watch your expensive fluid fall back out again, you should get about 3 litres.  Then, put the drain plug back in, pump 3 litres back in through the fill plug with the fitting and pump, disconnect the fill fitting and replace the fill plug, start the car and run for another 3 minutes (making sure the temp is still under 40oC). The manual then asks for a 3rd "spill and fill" just like above. I also did that and so had put 13l in by now.  This time they want you to keep the engine running and run the transmission through R and D (I hope the wheels are still off the ground!) for a while, and allow the trans temp to get to 40oC, then engine off. Finally, back under the car and undo the fill plug to let the overfill drain out; it will stop running when fluid is at the top of the levelling tube. According to the factory, that is job done! Post that, I reconnected the fill fitting and pumped in an extra 0.5l. AMS says 1.5l overfill is safe, but I started with less to see how it goes, I will add another 1.0 litres later if I'm still not happy with the hot shifts.
    • OK, so regardless of whether you did Step 1 - Spill Step 2 - Trans pan removal Step 3 - TCM removal we are on to the clean and refill. First, have a good look at the oil pan. While you might see dirty oil and some carbony build up (I did), what you don't want to see is any metal particles on the magnets, or sparkles in the oil (thankfully not). Give it all a good clean, particularly the magnets, and put the new gasket on if you have one (or, just cross your fingers) Replacement of the Valve body (if you removed it) is the "reverse of assembly". Thread the electrical socket back up through the trans case, hold the valve body up and put in the bolts you removed, with the correct lengths in the correct locations Torque for the bolts in 8Nm only so I hope you have that torque wrench handy (it feels really loose). Plug the output speed sensor back in and clip the wiring into the 2 clips, replace the spring clip on the TCM socket and plug it back into the car loom. For the pan, the workshop manual states the following order: Again, the torque is 8Nm only.
    • One other thing to mention from my car before we reassemble and refill. Per that earlier diagram,   There should be 2x B length (40mm) and 6x C length (54mm). So I had incorrectly removed one extra bolt, which I assume was 40mm, but even so I have 4x B and 5x C.  Either, the factory made an assembly error (very unlikely), or someone had been in there before me. I vote for the latter because the TCM part number doesn't match my build date, I suspect the TCM was changed under warranty. This indeed led to much unbolting, rebolting, checking, measuring and swearing under the car.... In the end I left out 1x B bolt and put in a 54mm M6 bolt I already had to make sure it was all correct
×
×
  • Create New...