Jump to content
SAU Community

Recommended Posts

Hi Guys,

I have a had a set of 34 GTR wheels that are waiting to be put on my 34GTT

I think if memory serves, the wheels are 18x9 +30?

I'm looking at getting a really decent set of tyres, possibly something like the pirelli p zero's or equivalent.

All I'm really after is just to get the correct tyres for the rims and my car.

I have been looking for sometime at getting 265/35/18's all round, but after a bit of googling, it looks like they would be fine for the rear, but would need a different fitment for the front?

If you guys could offer a bit of assistance with my situation, that'd be great.

Cheers,

Jacob

Link to comment
https://www.sau.com.au/forums/topic/416198-tyres-for-my-34/
Share on other sites

245s would be ideal

Damo, what are you doing mate? Bad advice is bad.

What tyre profile would you run on an R34 GT-T with a 245 section width? 245/35 is too short and 245/40 too tall. If you really want something fat on the back run 225/40R18 on the front and 255/35R18 on the rear, otherwise a good quality 225/40R18 will be up to the job on a Skyline without ridiculous power.

OP also stated that he is looking at getting decent tyres, if he opts for a Toyo Proxes R1R (which I can't reccomend enough), Yoki Advan AD08 or similar these will have a wide contact patch for their respective sizes i.e a 255/35R18 R1R is usually as wide as a mid-range 265/35R18.

Edited by Hank Scorpio
Link to comment
https://www.sau.com.au/forums/topic/416198-tyres-for-my-34/#findComment-6681743
Share on other sites

255's look nice and beafy at the rear, especially with the +30 offset. Keep with 225's or 235's at the front I reckon, you don't want too much resistance when turning your wheel, it can get annoying! My ones are 40 at the front and 35's at the rear, 18's all round, they fit nice and snug

Link to comment
https://www.sau.com.au/forums/topic/416198-tyres-for-my-34/#findComment-6684662
Share on other sites

Either 225 40 18( will give it a slight stretch) or 235 40 18( better suited for performance)

And a 245 40 18 or 255 35 18 rear. Both will work nice on the rear on the 9". 265 rear you would want a 235 40 18 front.

And yes going too wide on the front will cause tram lining which does get VERY annoying!

Depends on what tyres you are looking to fit on.

Link to comment
https://www.sau.com.au/forums/topic/416198-tyres-for-my-34/#findComment-6686267
Share on other sites

I agree with Ali.

225/40/18 on the front, and a 255/35-40/18 on the rear.

For tyre selection, it comes down to the way you drive. Do you track it often? Do you daily it? Is it a weekend only car? Do you carry big loads? Would you prefer grip or longevity? How much did you want to spend?

There is a lot of factors to take into consideration when picking he right tyre for YOU, not just the right tyre in general.

Cheers,

Shazza

Link to comment
https://www.sau.com.au/forums/topic/416198-tyres-for-my-34/#findComment-6686281
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
×
×
  • Create New...