Jump to content
SAU Community

Recommended Posts

  • 1 month later...

Good to see your build is progressing.

It's a bit of a shame that you didn't end up trying a 1.5mm top ring. The results would have been interesting. I can't help but think there's a reason Nissan specified a 1.5mm top ring for the factory engine.

  • 1 month later...

Motor is back together and working. Some random thoughts.

1. Removed the back of head oil drain.

2. The oil cooler/warmer standard on an RB26 has got some weight to it. Removed that and replaced it with an RB20 unit (Thanks Troy). Running a filter with an oil relief in it now.

3. Drilling out the oil returns in the head is actually harder than people make it sound on the interweb. They are quite lengthy and the top is a little difficult to get to.

4. What I was told about the ring gaps in the old engine was a pack of lies - they were bigger than quoted.

I can relate with number 3. Cast is never very nice to drill, especially over great lengths. I think from memory I had to use long series 9mm drill bits. Then slightly blunten off the cutting edge so it was not so 'bitey' and want to pull itself through so aggressively.

What were the old ring gaps?

  • 2 months later...

Well the thing is back together and on the dyno. Problem now is it wont run more than 16lb for 410 horsepowers. Will run to 22 with the wastegate shut but the boost controller wont allow over 16lb. Bov's are fine. Actuators are HKS on -5 Garretts. Boost controller is a Blitz dual solenoid type. Any one with any clues?

Yes.

Tomei were my start point but I couldn't find a reference to an 86mm piston, only oversize ones.

Didnt look at ACL or Nitto (Not that the NItto list has an 86mm size anyway) because I didnt want to use them.

Have CP pistons currently and given the issues I have dont want to go back there either.

Nitto pistons are actually made by JE Pistons. Great bit of kit. They make custom items, so IMO, they are the best bet. If you know the size of your combustion chambers, deck height, and what head gasket you intend on running, you can order these with a custom crown / dish cc, thus giving you a custom and a lot more suitable compression ratio.

More info?

Does the power go up when you disconnect the WG and let it overboost or is it stuck on 410?

AFAIK it goes harder than 410 with more boost but I didnt ask for a number as I was short of time.

It was described to me as a boost control issue so the question is:

A set up issue with the controller - something stupid like hoses the wrong way about?

A component failure with the controller eg a stuffed solenoid of the twin solenoid controller?

Please note: I dont doubt the workshop those are just simplistic examples by way of um, examples

  • 1 month later...

Went to Collie on the weekend. For those who arent from WA it is a small country circuit which takes 50 seconds to get around. It is anticlockwise and if your engine is having oiling problems then Collie will show them up. Anyway the bottom line is there was no more than three drops out of the breather all day. So I am claiming victory and moving on.

Need to find a workshop now to sort the boost controller.

Good news! Do you think the tighter ring gaps was the main factor in reducing oil entering the catch can?

How about deleting the rear head drain? Do you think that had any bearing?

Good news! Do you think the tighter ring gaps was the main factor in reducing oil entering the catch can?

How about deleting the rear head drain? Do you think that had any bearing?

Honestly, no I dont any more. I did fixate on it for quite a while but the gaps in the piston rings I have arent at the low end of what people use and they work fine. I reckon its a combination of the Pacific Engine Parts rings and the CRC bore lube on start up followed by driving the thing immediately on engine start.

As for the drain, yes I pissed it off. Used the return in the sump as an extra vent for the blowby. Probably doesnt make a huge difference if your blowby is under control. Probably helps if it isnt.

Honestly, no I dont any more. I did fixate on it for quite a while but the gaps in the piston rings I have arent at the low end of what people use and they work fine. I reckon its a combination of the Pacific Engine Parts rings and the CRC bore lube on start up followed by driving the thing immediately on engine start.

As for the drain, yes I pissed it off. Used the return in the sump as an extra vent for the blowby. Probably doesnt make a huge difference if your blowby is under control. Probably helps if it isnt.

Glad to hear you have it under control!

I'll be interested to see how mine goes if/when I get down to Collie, venting the sump seems to make all the difference

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Mixing things up - installed some leather recaros to match the leather seat covered rear seats. Interior looks pretty schmick now except for some slight wear on the steering wheel which I will monitor and address if it becomes worse or actually noticeable!  
    • Didnt realise RB's had more then 1 head.
    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
×
×
  • Create New...