Jump to content
SAU Community

Recommended Posts

  • Replies 45
  • Created
  • Last Reply

Top Posters In This Topic

R33 gtr brembos are direct bolt on to z32. IF r33 gtr brembos are bolt on to r33, then in theory the z32 caliper 'dogbone' adapters will fit r33 and enable 324mm rotors with stock calipers.

Early ones were alum, later ones iron.

Regardless, it's a simple and cheap mod for 324mm rotors, assuming the r33gtr calipers are bolt on to 33gtst as I said in my first post.

Edited by MagicMikeZ32

So why'd you get them??

If you actually do go to the track just make sure you put in some good fluid and it will be fine..it will take you a year of track days before you kill the brakes at least and that's if your a hack or very fast, they should last much longer if you drive clean

I'm not sure what the specific concern is about ADR approved brakes lines when the calipers, pads and discs, or how they work as part of a system, are also not ADR approved?

I think it is because it is easy to build a caliper that actually works without breaking open and leaking your fluid out while you're trying to stop. But there was a time when the first braided lines were being tried by people when there were inferior ways of swaging the ends on and so on that led to them failing. The ADR regs for how brake lines were to be constructed (or the tests they had to pass at least) already existed, so they just made it a requirement that any aftermarket ones had to be ADR approved. Not that the requirement wasn't already there in effect anyway, but at least if you require that they have a specific approval number granted by the regulatory body, you have an effecttive filter to stop the carppy ones being used.

Sure, there may be good ones available that don't have approval, and it sucks to be them. But they could always get them approved and start selling in competition to those that already are approved. But, to recoup the cost of getting them approved they'd probably come out at the same price anyway, so you wouldn't have the situation like those cheapies on the eBay link being as cheap as they are.

Edited by GTSBoy

So why'd you get them??

If you actually do go to the track just make sure you put in some good fluid and it will be fine..it will take you a year of track days before you kill the brakes at least and that's if your a hack or very fast, they should last much longer if you drive clean

Thought Ill give them a shot, im not going to be doing alot of track work, mainly just deca, haunted hills type stuff so I think these will be fine.

Definently will put good fluid in, will also do brake stopper and braided lines.

I'm not sure what the specific concern is about ADR approved brakes lines when the calipers, pads and discs, or how they work as part of a system, are also not ADR approved?

I personally wouldn't trust any brake line from overseas or that isn't adr approved, I guess if its adr approved theres less chance of a failure. I've seen a few jap branded braided lines burst but never a Hel one.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • 9" wheels are a little too wide for a RWD 32. They can fit. People have put R33 GTR wheels on 32s for years and years. But they are a very tight squeeze. This has been known for about 30 years. As I said - there is no difference between a 17 and an 18 in terms of what will fit. The rolling diameter needs to stay about the same as stock - not very much larger. If you increase that, you will start to have problems. If you increae rolling diamater at the same time as yo increase width, you will have problems earlier. as 9" wheels are pushing the boundaries already, you would need to be careful with tyre choice. I would put 8.5s on the front of mine, but would expect problems with 9s.
    • post up screen shots of your injector tables
    • Diagnostic flow for a code 21 says check signal at the ECU pins, on a voltmeter of some kind it should read 0.1V at idle, 0.12V cranking, 0.15-0.25V at 2000 rpm. Check each coil such that +1, -3 is infinite or very high resistance, -3, +2 should do the same. (-1, +3), (+3, -2), (+1, -2), and (-1, +2) should all be somewhere between 0 ohms and high resistance. If you trace the path from the coil pin all the way back to the ECU in the diagram the resistance you measure at the coil vs connected to the harness should be pretty much the same. 
    • I have an elite 2500 running an adapter harness on an rb25de neo r34. I took the butterfly out and removed all that junk. But I also went Plus+t at the same time. The butterfly thing works in reverse to the boost solenoid on the Gtt if that makes sense
    • yeh they are 235/45/17 up front and 255/40/17 in the rears. I still didn't get my answer if i can fit a 18x9 up front. I want to get 4 of this and see if they will fit before committing as they didn't see an 18x8 as an option but there is a 18x9.5 also.   Enkei RS05-RR 18x9 35mm ET 5x114.3 75.0 Bore Matte Gunmetal Wheel
×
×
  • Create New...