Jump to content
SAU Community

Big Brake Group Buy #2 - Skyline / Silvia / Stagea / Wrx / Evo / All Makes/models


Recommended Posts

I'm in for a r33 gtst front kit 356mm, street pad, anodized black, but not 100% sure yet on colour, is that alright to update later if I change my mind on colour?



Listing:
1. geetea-are - 356mm Front only / R32 GTS-t - Race Pad - Anodised Black
2. calcal - 356mm Front only / R32 GTS-t - Race Pad - Anodised Black
3.
4.
5.
6.
7.

Im not sure if it makes a difference but my car is a r32 gt-r not gts

  • 2 weeks later...

I so want in on this. I'm doing my darndest to find a spare $1800.

One question, and a long shot, I don't suppose any of these kits would fit an X series Falcon? (XA-XC and XD-XF) Also might have a mate keen on a set for a BA XR8 if any of them will fit.

Im not sure if it makes a difference but my car is a r32 gt-r not gts

Updated! :)

After thinking a bit more, i am going to pull out of this, as i think its overkill for my setup.

Ok updated.

I so want in on this. I'm doing my darndest to find a spare $1800.

One question, and a long shot, I don't suppose any of these kits would fit an X series Falcon? (XA-XC and XD-XF) Also might have a mate keen on a set for a BA XR8 if any of them will fit.

Only what is on their website is what they have kits for. So it would need to have a new dogleg made up to mount it (and ensure you get the right kit to suit the PCD) and you should then be fine!

will the 356mm Fronts fit on LMGT1 17 inch?

All 356mm kits require 18" wheels mate.

  • 2 weeks later...

Are D2's any different to ATTKD brake kits?

Also, I have a set of Nismo braided lines, would they be compatible with these brakes? Race pads and rotors are easy to source correct?

And is this group buy at risk of not happening due to numbers?

Cheers

Same stuff essentially.

As the mounting of the kit actually comes with a new arm - they might be ok (just depends on how much spare length you have).

Rotors can be sourced via Import Monster moving forward, and are cheap :)

It'll happen - just needs interest. First one is just about done

G'day Nismoid can u pls put me down for the following setup, cheers:

- Anodized Black 356mm Fronts with Race Pads for an R34 GT-T on the Gold Coast

Also, do you know of & recommend any brake specialist to install these kits around the Goldie &/or Brisbane areas???

Thanks again!

Edited by LoNg_ShaNks
  • 2 weeks later...

Looks like ill be selling my front and rear brake set and it wont clear my deep dish rims

356mm Front / R32 GT-R - Street Pad - Anodized Black

330mm Rear / R32 GT-R - Street Pad - Anodized Black

pickup only in western sydney, pm me

  • 2 weeks later...

What sort of time are we looking at for the next round? I would like a purple set for a 32gtr 356mm front and 330 rear with street pads and the handbrake kit to cairns

  • 11 months later...
  • 1 month later...

Definitely, though our pricing has reduced quite a bit anyway due to the stronger AUD since we originally conducted this GB

  • 4 weeks later...

Awesome id be keen on a 356mm front set in black for 33 gts-t. How far off before starting over again aaron?

I'm good to go whenever, not sure if the rules allow me as a business trader to conduct the group buy myself and I know that Ash has far too much on his plate right now

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I wasn’t able to replicate the sound anymore. It was a one time sound so maybe it was just coincidence but it was like small pebbles being dropped in a coke can.   should I try cleaning the MAF? It could be it’s functioning but dirty? I don’t know.
    • Update 4: Hi all. The car drives again! Haven't driven for long, only to store it in the garage again, but the test drive was successful. The coolant and oil leaks seem to be fixed for now. Temps on the engine were also very good, while moving I never even saw 80C water during the approx. 30 minute drive. Ate up all the coolant in the reservoir though so will have to fill that even more when I go to the car next time. One thing that pisses me off is that the RPM gauge is still f**ked, I even resoldered the board twice and used copper paste on the silly screws that are used as connections. Next time I take it out I'll take apart the board and fit new components, I'll see if I can get a replacement IC for it.  I have an appointment set for 22nd of September for the engine tune to 370hp. Alignment also still needs to be done. My hope is that I can get all the legal stuff over with by the end of this season. Anyone of you have advice regarding intercoolers? Currently there is an APEXI core fitted, one of those weird hybrid ones, 600x270x76. I don't think it's bad but it's not new and now I still have the chance to change it now to legally include it in the paperwork. Only issue is that the only options that would arrive in time are a HKS Type R intercooler or generic Ebay spec intercoolers comparable to a JustJap one. Ideally I'd order a Plazmaman but it takes over a month to receive which would mean making the car legal has to wait until next season. Would love to hear some input on this. Same story for my injectors, the previous owner was a nunce and put ID 1050x on the engine. They work but are obviously not ideal at "normal" power levels. But I don't see a reason to change them unless the tuner says it's necessary. I read online before buying a different exhaust that the top secret style rear diffusers won't fit due to the size of the rear resonators. My buddy and I made it work by slightly "adjusting the shape" of the mounting bracket and making some spacers out of 3d print for the mounting bolts. Fits like a charm. Just putting this here in case someone has this problem. Even the hefty HKS Silent Hi Power rear can fits without hitting anything.
    • Well they got my money but they are not getting my gearbox ! 
    • It's needed for rolling idle up, and I think it is a decider on VCT also.
    • I mean, not really. Link ECU's can absolutely still have errors from the ECU thinking it's getting a sensor it's not expecting. I would imagine the speed at the ECU level in Nistune does absolutely nothing anyway? I assume the ECU does not do any fancy TC stuff with regards to front+rear wheel speed or anything of that like anyway. Someone who uses Nistune may be more fluent in it. 
×
×
  • Create New...