Jump to content
SAU Community

Recommended Posts

  • Replies 297
  • Created
  • Last Reply

Top Posters In This Topic

.

Some should be excluded though, yourself, Nick and Simon. No one on here will beat Ghosty at this challenge, or most challenges

No one is excluded.., "most challenges" hey.. I'm sure I can think a few challenges that wouldn't be so one sided.... Apparently

Only problem is im a sook and my hands get rooted from work as a cabinet maker/installer so i use wraps to ease the pain and damage. Otherwise id do it, as its deads day for me today.

if I could edit the original post I'd add those excuses next to the coil pack issues.

says the guy who also says "not competing yet till I get a little stronger"

lol

It was more to do with the first doable novice comp being around April/May - incidentally enough time to gain some strength. I'll compete anyway, I just hope to be stronger by then.

Sounds like fun! I don't really care about the winning part. Any challenge can be applied against yourself.

Hard choice on the percentage vs standard weight because.... Well I have put on weight since I started gym and most of it is fat weight. Anyway!

I'm cool without gloves but is chalky chalk ok?

chalk is always welcome

Might have to look into this more.

I currently weigh in at 84kg ,

Was zapped today from heat, no excuse though i thought i preped before gym well. I believe there is plenty of room for improvement on that effort. I will see if i can get a video tomorrow when little less busy.

So is this a 1.5x bodyweight or 100kg? was it decided?

My deads today included a set of 145kg for 12 reps. @ 96.5kg. My first deads in a very very long time....

I think I'd like to do 20 or so reps of 145kg before the end of Jan, hopefully I can vid the success in the next week or so.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • I was 99% sure the standard one is long enough to get there, you might just have to change the throttle orientation. If not, I remember someone having used an r31 cable instead, but that is probably harder to find than r33 by now...
    • HELP   Hey all, Is there an accelerator cable from another Nissan that can be used on the R33 GTST RB25DET with a Greddy forward facing plenum?  Thanks in advance  Rob 
    • Or do we think it was installed to give 1 bar of boost max, all day, everyday?
    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
×
×
  • Create New...