Jump to content
SAU Community

Recommended Posts

  • Replies 44
  • Created
  • Last Reply

Top Posters In This Topic

Thanks yeah they will fit but im more wondering if there legal to have diffrent width wheels being an 1/1.5" diffrence

the example was just something random lol but that was the idea diffrent widths, looking at a set of wheels and its seems everyone sells staggered set, i would rather run all the same around but can't seem to find any ones to my liking

The answer is yes it is legal to have staggered fitmenf, your wheels cannot stick out of the guards, and your tyres have to be the correct recommendation sizes for the rim and the load rating for the car.

Been looking for months now :( just really sick of the look of stock wheels lol

ohh i see that makes sense no nothing over the top really

Would those tyre calculators online be okay to work off?

nah just head over to the fitment thread in the other section. have a read, youll find some decent sizes.

look at this link for any info regarding legal mods in Victoria

http://www.vicroads.vic.gov.au/NR/rdonlyres/CC48FC10-4D57-4F04-82E1-3BD72EF88340/0/VSI8.pdf

it says:

"the width of any replacement rim must not be:

- more than 25mm more than the widest wheel specified by the vehicle manufacturer for that model or vehicle series; or

- less than the width of the narrowest rim specified by yada yada yada yada...

not sure if "model or vehicle series" limits those conditions to the ER34 (the GT, GTT, GTV) or that extends to the GTR if you wanted to legally stretch an extra few mm's.

yeah.... sizes mentioned are illegal...

but so is breathing loudly in vic

but cars come factory with wider rims on the back so of course it's not an issue there

just buy the rims you want and be done with it... you are putting them on a skyline, so you'll get defected eventually no matter what rims you run so you might as well have the car looking how you want

also those sizes will look like aids

need to look at 18x9+20 all round as a MINIMUM

I', running staggered atm 8's front 9s rear.

makes it easier to get tyres to fit properlya nd still get he preformance I want.

Planning on staying stagerd but moving up a couple inches on each shortly.

well if I can get my arse into gear and get sunkist to sort my shit out.

<p>Gtst tyre placard on mine says stock rims are either 16 x 6.5 or 17x 8 and 17x 9 so legally you can run 9s and 10s respectably and you can use an 18 inch rim too...not sure about rules on offsets but you must not have tyre/rim that protrudes the outer edge of your car..anything between about +15 and +38 fits up ok with some guard rolling...<p>

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • HELP   Hey all, Is there an accelerator cable from another Nissan that can be used on the R33 GTST RB25DET with a Greddy forward facing plenum?  Thanks in advance  Rob 
    • Or do we think it was installed to give 1 bar of boost max, all day, everyday?
    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
×
×
  • Create New...