Jump to content
SAU Community

For Those Running Nismo Coppermix Twin.....

Goombeh
 Share

Recommended Posts

Goombeh Collaborator

Goombeh

Posted
Posted

So I've recently had my Nismo Coppermix Twin plate installed in the GTR and I'd read so much about them being very drivable and stock like.

Now I've only driven maybe 50kms so may be too early and may need bedding in, but immediate impressions are that it is very... very light. Doesn't feel like it will hold power, almost feel like I need to take the booster off to get more feel. But it's very quiet and seems very strong. It's very quiet in neutral or with clutch dissengaged.

Now my question is for those who run one, is it normal for it to cause some driveline judder on gradual take up? My searches are suggesting no, however I have read that this is commonplace on twins. I can drive around it of course by taking it up with more revs, but wondering if I should be looking into replacing gearbox or engine mounts or if this may be considered normal. My old Clutch had a very slight judder only when cold.

What do you think?.

R31Nismoid Grand Master

R31Nismoid

Posted
Posted

That's what makes the Nismo Coppermix so driveable. It's not filthy heavy like a OS twin plate for example which over time is like kicking a bag of sand over and over.

The first 500-1,000kms it will be a little bitey, it will settle down though. So give it a little while before worrying about minor shudder.

R31Nismoid Grand Master

R31Nismoid

Posted
Posted

it says that these clutches make noise and vibrations

Yeah just so that when it does make the slightest noise (and it literally is non-existent) - people dont come back and complain.

As the plates get lower/wear they will get noisier, just how it goes.

Iron Chef Grand Master

Iron Chef

Posted
Posted (edited)

My only complaints are it's a bit rattly on idle in neutral (clutch out) because of the flywheel, and slips a bit when cold, aside from that it's brilliant, very light to use and bites hard on high RPM take-offs...

Edited by Iron Chef
LotusGTR Veteran

LotusGTR

Posted
Posted

I've got one and I could not fault it in any way. When it was installed it was very 'bitey' (probably me just getting used to a twin) but I did get it adjusted (dunno what was done) and it was so much easier to use. No noises what so ever. Not heavy. Very user friendly. No driveline shudder under any circumstances.

Have only launched in 2WD mode but it was a 2nd gear start from standstill. No dramas and was really easy to modulate.

Ace clutch. Should be for the money.

nomnomv8 Rising Star

nomnomv8

Posted
Posted

Ive got the Coppermix Twin C-spec in mine and have nothing but praise for it. By far the easiest twin plate I have ever driven and at the same time has a real good bite to it. A few of the guys have mentioned noise issues - you can hear it on the odd occassion in neutral however its pretty subtle and honestly nothing to lose sleep over.

Give it about 500km or so of driving (start/stop as opposed to highway kms) before you give it a launch, I guarantee you it will definately "hold the power" ;)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      33 GTR Broken front wheel knuckle

      By GTSBoy · Posted

      There's plenty of OEM steering arms that are bolted on. Not in the same fashion/orientation as that one, to be sure, but still. Examples of what I'm thinking of would use holes like the ones that have the downward facing studs on the GTR uprights (down the bottom end, under the driveshaft opening, near the lower balljoint) and bolt a steering arm on using only 2 bolts that would be somewhat similarly in shear as these you're complainig about. I reckon old Holdens did that, and I've never seen a broken one of those.
    • MBS206
      33 GTR Broken front wheel knuckle

      By MBS206 · Posted

      Let's be honest, most of the people designing parts like the above, aren't engineers. Sometimes they come from disciplines that gives them more qualitative feel for design than quantitive, however, plenty of them have just picked up a license to Fusion and started making things. And that's the honest part about the majority of these guys making parts like that, they don't have huge R&D teams and heaps of time or experience working out the numbers on it. Shit, most smaller teams that do have real engineers still roll with "yeah, it should be okay, and does the job, let's make them and just see"...   The smaller guys like KiwiCNC, aren't the likes of Bosch etc with proper engineering procedures, and oversights, and sign off. As such, it's why they can produce a product to market a lot quicker, but it always comes back to, question it all.   I'm still not a fan of that bolt on piece. Why not just machine it all in one go? With the right design it's possible. The only reason I can see is if they want different heights/length for the tie rod to bolt to. And if they have the cncs themselves,they can easily offer that exact feature, and just machine it all in one go. 
    • Bennym35
      New guy

      By Bennym35 · Posted

      The roof is wrapped
    • Duncan
      R34 GT-T cycling ABS pump

      By Duncan · Posted

      This is how I last did this when I had a master cylinder fail and introduce air. Bleed before first stage, go oh shit through first stage, bleed at end of first stage, go oh shit through second stage, bleed at end of second stage, go oh shit through third stage, bleed at end of third stage, go oh shit through fourth stage, bleed at lunch, go oh shit through fifth stage, bleed at end of fifth stage, go oh shit through sixth stage....you get the idea. It did come good in the end. My Topdon scan tool can bleed the HY51 and V37, but it doesn't have a consult connector and I don't have an R34 to check that on. I think finding a tool in an Australian workshop other than Nissan that can bleed an R34 will be like rocking horse poo. No way will a generic ODB tool do it.
    • GTSBoy
      33 GTR Broken front wheel knuckle

      By GTSBoy · Posted

      Hmm. Perhaps not the same engineers. The OE Nissan engineers did not forsee a future with spacers pushing the tie rod force application further away from the steering arm and creating that torque. The failures are happening since the advent of those things, and some 30 years after they designed the uprights. So latent casting deficiencies, 30+ yrs of wear and tear, + unexpected usage could quite easily = unforeseen failure. Meanwhile, the engineers who are designing the billet CNC or fabricated uprights are also designing, for the same parts makers, the correction tie rod ends. And they are designing and building these with motorsport (or, at the very least, the meth addled antics of drifters) in mind. So I would hope (in fact, I would expect) that their design work included the offset of that steering force. Doesn't mean that it is not totally valid to ask the question of them, before committing $$.
×
×
  • Create New...