Jump to content
SAU Community

Recommended Posts

http://www.r31house.co.jp/season2/used_detail2.php?car_code=310058

gtp006a.JPG

~$6,600 AUD, add skirts and a rear bumper and that'd be killer!

If you had some serious ke$h I'd be after this GTS-R though...

http://www.r31house.co.jp/season2/used_detail2.php?car_code=310051

gtsr013a.jpg

(I'm assuming the RB26 equipped GTS-X available would be a hassle importing due to the engine)

  • 2 months later...

so,any updates mate? did you decide on what you are getting?

another option,rather than DR30, have you considered early HR30 coupe? L28 bored and stroked to 3.1, lumpy cam and big carbs, and with the early model coupes at barely 1100kg ish would be a sweet ride!

  • 2 weeks later...

Been having some engine trouble with my DC2R, which more or less threw cold water on getting a sweet older ride anytime soon. Right now just saving cash so I can get it looked at and hopefully fixed, but smoke billowing out from the exhaust is never a good sign :(

Rang up Seeker and they said $3000 for a head gasket, and about $7000 to reco the engine! Damn... Seriously hoping I can get it done cheaper than that!

Still clinging to the hope that I will have enough coin by the end of the year to pick up an older ride. I was keen to get an Evo 7/8, but after riding in my friends totally worked 8MR recently, I have to say I was left a bit wanting. It didn't feel fast at all. And if it did feel mildly quick, it was in a very techno/industrial/agricultural way as is the case with most Subies/Lancers...didn't feel sporting at all. Next option is an FD RX7 to bring back home, and can get an engine rebuild here for about $2500-3000. Was thinking of getting a good and clean but higher mileage one on the cheap and freshening up the engine before bringing it back. But now with the exchange rate plummeting and the head aches of compliancing and all the other jazz that will happen with any SEVS car, the easy way out is to just pick up a modified sick older ride. I'll probably be leaving Japan end of the year, and might not be bothered with the hassle of a SEVS import, so may just do the pre-89 rule car plus my Integra.

Still keen on a two-door FJ20 DR30, an AW11 MR2 4AGZE targa-top, or even a 3.0 litre manual old-school Soarer. An '88 CA18 S13 Silvia would be nice too, but S13's are probably cheaper in Australia than Japan now these days.

Good thing about the pre-89 cars, is that the rules on having new tyres/compliancing/must be totally standard and all the other jazz they expect of SEVS cars isn't anywhere near as strict. Could bring one over with mild mods and it wouldn't be an issue. I like that.

  • 2 weeks later...

Been having some engine trouble with my DC2R, which more or less threw cold water on getting a sweet older ride anytime soon. Right now just saving cash so I can get it looked at and hopefully fixed, but smoke billowing out from the exhaust is never a good sign :(

Rang up Seeker and they said $3000 for a head gasket, and about $7000 to reco the engine! Damn... Seriously hoping I can get it done cheaper than that!

Still clinging to the hope that I will have enough coin by the end of the year to pick up an older ride. I was keen to get an Evo 7/8, but after riding in my friends totally worked 8MR recently, I have to say I was left a bit wanting. It didn't feel fast at all. And if it did feel mildly quick, it was in a very techno/industrial/agricultural way as is the case with most Subies/Lancers...didn't feel sporting at all. Next option is an FD RX7 to bring back home, and can get an engine rebuild here for about $2500-3000. Was thinking of getting a good and clean but higher mileage one on the cheap and freshening up the engine before bringing it back. But now with the exchange rate plummeting and the head aches of compliancing and all the other jazz that will happen with any SEVS car, the easy way out is to just pick up a modified sick older ride. I'll probably be leaving Japan end of the year, and might not be bothered with the hassle of a SEVS import, so may just do the pre-89 rule car plus my Integra.

Still keen on a two-door FJ20 DR30, an AW11 MR2 4AGZE targa-top, or even a 3.0 litre manual old-school Soarer. An '88 CA18 S13 Silvia would be nice too, but S13's are probably cheaper in Australia than Japan now these days.

Good thing about the pre-89 cars, is that the rules on having new tyres/compliancing/must be totally standard and all the other jazz they expect of SEVS cars isn't anywhere near as strict. Could bring one over with mild mods and it wouldn't be an issue. I like that.

Make sure you do all the paperwork properly for the personal import before it leaves, proving how long you have had car for etc, parking rental reciepts etc

Why dont you get some ae86's? theres plenty that i see on yahoo jp that could be brought back for a fair profit

Otherwise id bring a few track cars back, s15/fd/jzx100 etc

Pm me if you need container help, lands bris tho, and yards in osaka

Make sure you do all the paperwork properly for the personal import before it leaves, proving how long you have had car for etc, parking rental reciepts etc

Why dont you get some ae86's? theres plenty that i see on yahoo jp that could be brought back for a fair profit

Otherwise id bring a few track cars back, s15/fd/jzx100 etc

Pm me if you need container help, lands bris tho, and yards in osaka

Thanks mate. I'll send you a PM. Might have to see what you could help me bring in - as I could have a car complied (if its a SEVS car) in QLD, then have it brought over to WA I suppose?

Most of the AE86s here for sale are DOGS. You do see the occasional one in a not-so-sought after color/trim/bodystyle combo that is still a great condition car but nobody wants it, as they are all fanboys here looking for the clones of various D1 cars, famous manga/anime AE86s and so on.

I have the feeling that back in Australia, people wouldn't be so picky?

C130 Laurels start at around $10k, and stretch to as much as $30k. Most are around the $15k - $25k mark. Way too expensive.

Shame of the stupid pre-89 rule... I'd love a C33 Laurel.

When will this dumb rule change? I mean, these cars are 25 years old now. Surely the gov't will wake up and change this law and eventually make it pre-90, or pre-91 etc etc as the years go by. Does anybody know if this ruling will change? Or is it still going to be pre-89 only even years from now?

Will change to the 30 year rule in 2019.

When they are all rusted-out sh*tboxes that pose absolutely ZERO threat to the locally delivered Australian models (which is ostensibly the motive for the gov't to be so draconian). Hell, they are already zero threat now.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
    • The video for the servicing and fuel filter change can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44 One of the main jobs I wanted to do before the car officially went on the road, was to remove the awful looking blue silicone hoses. There's nothing wrong with having coloured silicone hoses, but I realise as I'm getting older I prefer monotone engine bays with a splash of colour on the engine cover(s). I cover this in a lot more detail in the Youtube video, so unfortunately there's limited photos of the process. The intercooler, upper radiator, boost vacuum and upper breather hoses were all changed to black silicone with mikalor clamps. The only blue left is a blanking cap at the back of the inlet manifold and the GReddy pulleys (which will be replaced for stock when the cambelt gets replaced) While the intercooler pipes were off I gave them a quick clean/polish too A before photo I do have a replacement air filter on its way. Fuse box covers were painted blue, they're now satin black Another job on the list while the bumper was off, is to add some mesh https://live.staticflickr.com/65535/54737966256_99b28bfa30_c.jpg[/img] I was hoping to use some thin wire to secure it, but it seems I've misplaced it and the wire I had was too thick to twist easily. I ended up using cable ties for the time being https://live.staticflickr.com/65535/54737131882_c2b7989dcc_c.jpg[/img] Was pleasant to see this https://live.staticflickr.com/65535/54737131627_8b2aab13b3_c.jpg[/img] The last thing to do was to fix the front grill and re-mesh that to match but I ran out of time The Youtube video can be seen here: https://www.youtube.com/watch?v=R4FsF6tgizE&t=23s
×
×
  • Create New...