Jump to content
SAU Community

Nistuning; Who Does It Act

Pattey21

By Pattey21,
in Australian Capital Territory

 Share

Recommended Posts

Sinista32 Grand Master

Sinista32

Posted
Posted

I wouldn't think so.

My experience is a tune from scratch is over $1k and a retune around $400

I haven't used Autotech but pick up the phone and call them. (25c) :)

Jez on the central coast is good with Nistune's and I beleive reasonable on price

FJ 720 Community Regular

FJ 720

Posted
Posted

I was more than happy with the nistuning autotech did on my sr20det 1600. I got PLMS to supply the nistune with a base map loaded to suit my injectors/AFM/turbo, and got autotech to do the fine tuning. From memory it was around the $400-$500 mark and netted 220rwkw @ 14psi with drivability of a factory ecu.

the_moose Contributor

the_moose

Posted
Posted

Also had Nistune installed and tune by Ed at Autotech. Car has done many track days and hasn't skipped a beat 215rwkw (Silvia SR20DET)

Unless your going monster power is more than adequate.

He is very expensive but still cheaper than dragging your car to Sydney to get it done.

Guest

Guest

Posted
Posted (edited)

I was more than happy with the nistuning autotech did on my sr20det 1600. I got PLMS to supply the nistune with a base map loaded to suit my injectors/AFM/turbo, and got autotech to do the fine tuning. From memory it was around the $400-$500 mark and netted 220rwkw @ 14psi with drivability of a factory ecu.

$500 for a tune? thats retune price isnt it?

would 350kw be classified as big power?

on a GTR

Edited by AnDreeZy
FJ 720 Community Regular

FJ 720

Posted
Posted

That's roughly what I've paid for every tune I've had done there, all have been retunes I.e. change supercharger to turbo, install bigger turbo and cams, fuel system upgrade. I guess the nistune was a retune as I was driving it for months on the base map no worries.

Anfanee Grand Master

Anfanee

Posted
Posted

For my GTR i was quoted $1200 to re chip and nistune the ECU from autotech. $500 for a re tune if usually what you will pay.


$500 for a tune? thats retune price isnt it?
would 350kw be classified as big power?
on a GTR

I wouldn't classify it as "Big" power but it's a lot none the less. You don't really want much more than that for a road car. Unless you are a dyno dummy. But after that you usually have so much lagg/Too much power you lose most of the fun.

GTRKat Grand Master

GTRKat

Posted
Posted

350kw on a GTR is effortless and not classified as big power.

I have a lot more than is necessary for a street car but I happen to like drag racing. Mine's also a lot more drivable than you think, you just need to go to some effort to make sure you set things up properly.

Reese69 Proficient

Reese69

Posted
Posted

not sure how the nis tune thing works - but when it come to tuning you pay for what you get and Ed might be more pricey then others - not much - but he is worth every cent in my opinion - and has great results in a wide range of cars, engines and ecu's-

in my opinion put the extra in and go to him rather then saving a few bucks -

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Waders360
      M35 Brake caliper replacement

      By Waders360 · Posted

      Sorry. Front brake calipers
    • MBS206
      S1 rb25/s14 starting problem

      By MBS206 · Posted

      Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      I checked spark on all cylinders and they all visually have spark with the plug pulled and grounded, but plug 1 is the only one that fouled. This was a running swap that blew up and was rebuilt by a machine shop, put a new wiring specialties harness and did all gaskets, studs, and bolts while it was out.  compression is 135-150 across all cylinders. Aside from that from my understanding with the z32 ecu and maf the car should start regardless. The wiring for TPS and the dual 02 sensor/ dual knock sensor stuff shouldn’t actually stop the car from starting or even running well, (just slightly rich)  they just give fault codes. Car supposedly is supposed to start as long as you have z32 afm and ecu with the nistune base map and that’s info coming from a well known and trusted tuner who does a lot with SR/RB (Rsenthalpy). After more trouble shooting today where I’m at right now is that the cas is sending signal to the injectors they click while spinning the rotor, Fuel pressure is now set at 43psi, all cylinders have good compression and all of the plugs looked great (just wet with fuel) except for cylinder 1 which was very black (cylinder 1 has 150psi compression). all of the coils generate spark if pulled out and grounded out on the head. On the fuel pump car just pops into the exhaust. On starting fluid car will fire off. Hard to tell if all cylinders are firing off but definitley a couple. sounds like all of them but it’s only for 3-5 seconds hard to tell. 
×
×
  • Create New...