Jump to content
SAU Community

Recommended Posts

Looking at fitting harnesses in my stag as when cornering at speed you have to brace yourself a bit at the moment. Anyone else fitted harnesses? Wanting to keep it practical with useable back seats so was thinking either a double release harness. Original plan was to put a harness mounting bar behind the front seats but not found any for stageas.

Link to comment
https://www.sau.com.au/forums/topic/419782-racing-harnesses/
Share on other sites

Yep I fitted a couple of Recaros from a Euro Honda or something - more comfortable than a race seat for my daily driver but heaps more control on the track. In this country (don't know about UK) if you fit a harness you have to be a member of a car club, run a log book etc.

Yeah reclining are ok. It's to do with cutting people out of cars. Harnesses have to have a red release button so can easily by identified and seats must recline so they can get you out on a spinal board. It's meant to come into affect in April, they tried about a year ago but realized none of the mot garages were prepared.

Yeah reclining are ok. It's to do with cutting people out of cars. Harnesses have to have a red release button so can easily by identified and seats must recline so they can get you out on a spinal board. It's meant to come into affect in April, they tried about a year ago but realized none of the mot garages were prepared.

As much as it pains me; that's actually a very smart policy.

At least there's logical reasoning at play in the decision making process; rather than the usual "Don't do it or we'll fine you" mentality we have in Australia...

Providing you have a WC34 Stagea a relativly cheap and good looking option is a pair of front seats out of a R32/R33/R34 GT-R. I believe they bolt straight up!

Personally I wouldn't be using a harness on the street anyway. While you are strapped in you can't move your body to look around properly (ie checking blind spots while merging lanes and parking)

  • 1 year later...

Honestly I found I could corner much faster while held in with a decent seat - I have used an aftermarket bucket seat and also a Recaro from a Euro Honda and both gave excellent results. I suspect a GTR seat would be also be ok and would have the advantage of bolting straight in to the existing holes without the need for an aftermarket seat base and slider.. As part of my cert process I had to fit seat belt anchors to the transmission tunnel so pretty secure as well.

You do realize that the back seats have to be removed and the belts must go back as straight as possible so as when you go over you body weight doesn`t go on your shoulders >back , Cams stipulation read the regs also road authority.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm looking for some real world experiences/feed back from anyone who has personally ran a EFR7670 with a 1.05 exhaust housing or a .83 I'm leaning towards the .83 because its a street car used mostly for spirited driving in the canyons roads. I"m not looking for big numbers on paper. I want a responsive powerband that will be very linear to 8000 rpm. I dont mind if power remains somewhat flat but dont want power to drop off on top. The turbo I've purchased is a 1.05, although the mounting flange T3 vs T4 and internal vs external waste gates are different on both housings, I not concern about swapping parts or making fabrication mods to get what I want. Based on some of the research I've done with chat gpt, the 1.05 housing seems to be the way to go with slightly more lag and future proofing for more mods but recommends .83 for best response/street car setup. AI doesn't have the same emotions as real people driving a GTR so I think you guys will be able to give me better feed back 😀   
    • Surely somebody has one in VIC. Have you asked at any shops?  Is this the yearly inspection or did you get a canary?
    • This is where I share pain with you, @Duncan. The move to change so many cooling system pieces to plastic is a killer! Plastic end tanks and a few plastic hose flanges on my car's fail after so little time.  Curious about the need for a bigger rad, is that just for long sessions in the summer or because the car generally needs more cooling?
    • So, that is it! It is a pretty expensive process with the ATF costing 50-100 per 5 litres, and a mechanic will probably charge plenty because they don't want to do it. Still, considering how dirty my fluid was at 120,000klm I think it would be worth doing more like every 80,000 to keep the trans happy, they are very expensive to replace. The job is not that hard if you have the specialist tools so you can save a bit of money and do it yourself!
    • OK, onto filling. So I don't really have any pics, but will describe the process as best I can. The USDM workshop manual also covers it from TM-285 onwards. First, make sure the drain plug (17mm) is snug. Not too tight yet because it is coming off again. Note it does have a copper washer that you could replace or anneal (heat up with a blow torch) to seal nicely. Remove the fill plug, which has an inhex (I think it was 6mm but didn't check). Then, screw in the fill fitting, making sure it has a suitable o-ring (mine came without but I think it is meant to be supplied). It is important that you only screw it in hand tight. I didn't get a good pic of it, but the fill plug leads to a tube about 70mm long inside the transmission. This sets the factory level for fluid in the trans (above the join line for the pan!) and will take about 3l to fill. You then need to connect your fluid pump to the fitting via a hose, and pump in whatever amount of fluid you removed (maybe 3 litres, in my case 7 litres). If you put in more than 3l, it will spill out when you remove the fitting, so do quickly and with a drain pan underneath. Once you have pumped in the required amount of clean ATF, you start the engine and run it for 3 minutes to let the fluid circulate. Don't run it longer and if possible check the fluid temp is under 40oC (Ecutek shows Auto Trans Fluid temp now, or you could use an infrared temp gun on the bottom of the pan). The manual stresses the bit about fluid temperature because it expands when hot an might result in an underfil. So from here, the factory manual says to do the "spill and fill" again, and I did. That is, put an oil pan under the drain plug and undo it with a 17mm spanner, then watch your expensive fluid fall back out again, you should get about 3 litres.  Then, put the drain plug back in, pump 3 litres back in through the fill plug with the fitting and pump, disconnect the fill fitting and replace the fill plug, start the car and run for another 3 minutes (making sure the temp is still under 40oC). The manual then asks for a 3rd "spill and fill" just like above. I also did that and so had put 13l in by now.  This time they want you to keep the engine running and run the transmission through R and D (I hope the wheels are still off the ground!) for a while, and allow the trans temp to get to 40oC, then engine off. Finally, back under the car and undo the fill plug to let the overfill drain out; it will stop running when fluid is at the top of the levelling tube. According to the factory, that is job done! Post that, I reconnected the fill fitting and pumped in an extra 0.5l. AMS says 1.5l overfill is safe, but I started with less to see how it goes, I will add another 1.0 litres later if I'm still not happy with the hot shifts.
×
×
  • Create New...